Marantz SD9000 - Page 27

(5) Timer cycle OFF-ON
The tape deck starts operating at the time preset in the
timer. This feature is used when using the deck as an
alarm or for unattended tape recording.
(In this case, the timer-off time should be cleared.
When the memory is cleared, the display indicates 0:00.
The timer-off function does not function at 0:00).
a. When the POWER switch is OFF during timer ON
stand-by: At the timer ON time, the power supply of
the tape deck is turned on. The external devices are
also supplied with AC power.
b. When the POWER switch is ON during timer ON
standby:
AC power is supplied to the tape deck and the ex-
ternal devices.
c. When the TIMER switch is in the REC position:
At timer ON, the tape deck functions as follows (the
parentheses indicate operation when the erasure pre-
vention tabs have been removed from the cassette).
[Condition 1: | REC/PLAY (PLAY)
Condition 2: |PLAY (Counter memory and program
are not possible.)
Condition 3: |PLAY (PLAY Operations are not pos-
sible.)
Condition 4: | PLAY (PLAY) "
d. When the TIMER switch is in the OFF position:
The power is controlled by the TIMER ON signal.
e. When the TIMER switch is in the PLAY position:
At timer ON, the tape deck functions as follows.
PLAY
Counter memory play operation
Condition 3: | Program play operation
Condition 4:
Program play operation
(6) Timer cycle ON-OFF
Set the tape deck to the PLAY or REC/PLAY mode.
The tape deck stops at the preset time. This feature is
also used for sleep timer operation.
At timer OFF, the tape deck stops. The tape deck also
stops if the tape reaches its end before the timer OFF
time. To turn off the AC power at the timer OFF time,
proceed as follows:
a. Turn the POWER switch ON.
b. Store the timer OFF time, then press the TIMER key
to start the timer.
c. Set the deck to the REC/PLAY mode.
d. At timer ON, the deck is set to the PLAY or REC/
PLAY mode. Turn the POWER switch OFF.
e, At timer OFF, the tape stops and, at the same time,
the AC power to the tape deck and the external de-
vices is turned off.
(7) Timer cycle OFF-ON-OFF
At timer ON, the tape deck is set to the PLAY or REC/
PLAY mode; at the timer OFF, the tape deck stops.
This feature is also. used when using the deck as an alarm
or for unattended tape recording. In this case, the timer
OFF function is added to the timer cycle OFF-ON in
the above item (5). The tape deck stops when the tape
reaches its end before the timer OFF time.
If the POWER switch is OFF, the power remains on
until‘the timer OFF time is reached even when the tape
stops automatically at the end of the tape.
Note that the timer OFF time should be set to a time.
later than the timer ON time.
(8) Timer cycle ON-OFF-ON
If the tape deck is in the PLAY or REC/PLAY mode, it
will stop at the timer OFF time, and start again at the
timer ON time. This feature is also used for sleep timer
operation or when used as an alarm. The timer ON time
should be set to a time later the timer OFF time. If it is
not required to interlock the timer with the power sup-
ply, leave the POWER switch in the ON position with
the tape deck started, then set the timer OFF and ON
times so that the timer operation command is given by
the TIMER key.
To interlock the timer with the power supply, use the
following procedure:
a. Turn the POWER switch ON.
b. Store the timer ON and OFF times, then press the
TIMER key.
c. Set the tape in the PLAY or REC/PLAY mode.
d. Turn the POWER switch OFF.
(9) Timer setting (special case)
When the hour display is other than 1 through 12, an
error signal is generated as noted in section 5.3 “CLOCK
SET”.
However, the clock cari be set to 0:00 only in the fol-
lowing cases.
* The power is connected to the tape deck and the CE/
RESET key is pressed after the POWER switch is
set to ON.
* At the CLOCK SET position of the SELECTOR
switch, the CE/RESET key is pressed after the PM
key has been pressed.
In either case, the clock starts operating when the CE/
RESET key is pressed. Therefore, the timer ON and
OFF times can be set using the time when the CE/
RESET key is pressed as a reference. In this case, the
setting time should be between 1:00 and 11:59, 12:00
PM and 11:59 PM, or 12:00 and 12:59.
(10) Others
a. When the time on the clock coincides with the timer
ON or OFF time during timer operation, the TIMER
ON signal is switched momentarily from low level to
high level, or vice versa. For example, if 9:05 is
stored in memory and the time on the clock advances
to 9:05, the TIMER ON signal is given momentarily.
In this case, the TIMER ON signal remains the same
even if 9:05 is stored in memory when the clock in-
dicates 9:05.
b. When the tape deck is in the PLAY or REC/PLAY
mode during timer operation, the operating mode
remains unchanged even if the TIMER switch is set
to another position.