What to do if Martin MAC Aura XB DJ Equipment fixture does not power up?
If your Martin DJ equipment fixture isn't powering up or resetting, the issue could be a blown fuse, a faulty PSU, or a faulty main PCB. Try replacing the fuse first. If that doesn't work, you may need to replace the PSU or the main PCB.
How to fix a fan error in Martin MAC Aura XB?
If you're encountering a fan error with your Martin DJ Equipment, the problem might be a faulty fan or a faulty fan driver. You can try replacing the fan. If replacing the fan doesn't solve the issue, the main PCB may be faulty and require replacement.
What causes a pan sensor error in Martin MAC Aura XB?
A pan sensor error in Martin DJ Equipment can be caused by several factors. The absolute position might not be found, in which case you should check the sensor and its wiring, replacing the sensor if necessary. Alternatively, the belt may be worn out or not properly tightened; try tightening or replacing it. Finally, the motor could be faulty, so check the motor and its cable, replacing them if needed. Replacing the main PCB may also be necessary.
How to troubleshoot tilt sensor error on Martin DJ Equipment?
To troubleshoot a tilt sensor error on your Martin DJ Equipment, consider these potential causes: the absolute position might not be found, so check the sensor and its wiring, replacing the sensor if necessary. The belt could be worn or not properly tightened; try tightening or replacing it. The motor might be faulty, so check the motor and the motor cable, replacing them if necessary. Replacing the main PCB may also be necessary.
Why does my Martin MAC Aura XB DJ Equipment show MAIN TMP SEN ERR?
The 'MAIN TMP SEN ERR' message on your Martin DJ Equipment indicates that the main PCB is too hot, the communication wire between the main PCB and LED PCBs is faulty, or the main PCB itself is faulty. Try replacing the fan. If the issue persists, replace the wire harness (P/N 11860396) that goes from connector PL16 to PL39 on the LED PCB. If neither of these solutions works, consider replacing the main PCB.
What does BEAM TMP SEN ERR mean on Martin MAC Aura XB DJ Equipment?
The 'BEAM TMP SEN ERR' message on your Martin DJ Equipment indicates a problem with the Beam LED PCB temperature sensor. This could be due to a faulty communication wire from the main PCB to the Beam LED PCB, the Beam LED PCB being too hot, or a faulty main PCB. Try replacing the wire harness (P/N 11860396) that goes from connector PL16 to PL39 on the LED PCB. If that doesn't resolve the issue, replace the Beam LED PCB or the main PCB.
How to resolve AURA TMP CUT OFF error in Martin MAC Aura XB?
The 'AURA TMP CUT OFF' error in Martin DJ Equipment suggests that the Aura LED PCB has a temperature issue. This could be caused by a faulty communication wire from the main PCB to the Aura LED PCB, the Aura LED PCB being too hot, or a faulty main PCB. Replace the wire harness (P/N 11860396) that runs from connector PL16 to PL39 on the LED PCB side. If the problem continues, replace the Aura LED PCB or the main PCB.
What to do for a voltage error on Martin MAC Aura XB?
A voltage error on your Martin DJ Equipment could stem from the thermal switch in the LED heat sink being open circuit or +88 VDC not being supplied to the main PCB. Check the thermal switch and replace it if necessary. Also, check the +88 VDC wire and replace the wire harness (P/N 11860395) if needed.
How to fix FBEP or FBET error on Martin MAC Aura XB DJ Equipment?
The FBEP or FBET error on Martin DJ Equipment can arise from several issues: a loose screw on the tacho wheel, damaged teeth on the tacho wheel, a faulty wire, a faulty sensor, a faulty main PCB, or a damaged or loose belt. Here are some steps to resolve the issue: * Tighten the screw on the tacho wheel. * Replace the tacho wheel if the teeth are damaged. * Replace the wire if it's faulty. * Replace the sensor if it's faulty. * Replace the main PCB if it's faulty. * Tighten the belt and replace it if necessary.
What to do if I get a BEAM CALIB ERR on my Martin DJ Equipment?
If you receive a 'BEAM CALIB ERR' message on your Martin DJ Equipment, it indicates that calibration values cannot be read from the Beam LED PCB. Check the communication wires from the mainboard to the Beam LED PCB and replace the Beam LED PCB, if necessary.
General| Light Source | LED |
|---|---|
| LED Lifetime | 50, 000 hours |
| Pan | 540° |
| Tilt | 270° |
| Control | DMX, Art-Net, sACN |
To Next Page
