Masterbuilt 20072912 User Manual

Masterbuilt Manufacturing, Inc.
1 Masterbuilt Ct.
Columbus, GA 31907
Servicio de atención al cliente: 1-800-489-1581
www.masterbuilt.com
SEA PARTE DE NUESTRA COMUNIDAD EN LÍNEA "DADGUM GOOD":
www.masterbuilt.com | www.dadgumthatsgood.com | www.facebook.com/masterbuilt
Twitter @Masterbuilt @JohnMcLemore @Dadgum atsGood
Masterbuilt Manufacturing, Inc. · 1 Masterbuilt Ct. Columbus, GA 31907 · Customer Service: 1-800-489-1581 · www.masterbuilt.com
090513-23GH
MADE IN CHINA
1
2
3
PART NO QTY DESCRIPTION
1 1 Tabletop
2 4 Leg
3 1 Bottom Shelf
Tools needed for assembly (not included): Phillips Head Screw Driver, Adjustable Wrench
ELECTRIC SMOKER STAND
For use with the following models:
20070213, 20070312, 20071214, 20071314, 20071414, 20071514,
20071614, 20071714, 20072112, 20072212, 20072312, 20072412,
20072512, 20072712, 20072812, 20072912, 20100714, 20101213
M6
Flange Nut
Qty. 16
B
DO NOT RETURN TO RETAILER
For Assembly Assistance, Missing or Damaged Parts
Call: MASTERBUILT Customer Service at 1-800-489-1581.
M6 x 50
Screw
Qty. 4
M10 x 55
Screw
Qty. 2
C
D
A
M6 x 12
Screw
Qty. 16
E
M10 Nut
Qty. 2
CALIFORNIA PROPOSITION 65
This product contains chemicals, including lead and lead compounds, known to the State of
California to cause cancer, birth defects or other reproductive harm.
Wash your hands after handling this product.
WARNING
Instructions For Use With Generation 2 Smokers

Masterbuilt 20072912 Specifications

General

Brand	Masterbuilt
Model	20072912
Type	Electric Smoker
Fuel Type	Electric
Power Source	Electric
Cooking Area	730 square inches
Temperature Range	100°F to 275°F
Power	800 watts
Temperature Control	Digital
Built-in Thermometer	Yes
Capacity	4 racks
Digital Control Panel	Yes
Removable Drip Pan	Yes
Wood Chip Loader	Yes
Construction Material	Steel

Summary

Masterbuilt Electric Smoker Stand

Instructions for Use

Guidance for using the electric smoker stand with Generation 2 smokers.

California Proposition 65 Warning

Alert about chemicals known to cause cancer or reproductive harm.

Smoker Stand Assembly

Step 1: Attach Bottom Shelf

Secure bottom shelf to legs using screws and nuts, do not fully tighten.

Step 2: Attach Legs to Tabletop

Secure legs to tabletop using screws and nuts, do not fully tighten.

Smoker Stand Installation

Step 1: Prepare Smoker

Position smoker upside down, remove footscrews, and prepare for stand attachment.

Step 2: Position Stand on Smoker

Place stand on upside-down smoker and loosely attach hardware.

Safety Cautions

Do not lift smoker alone or by the rear handle. Get a helper.

Smoker Stand Installation Continued

Step 3: Secure Stand with M10 Nuts

Thread M10 nuts onto M10 screws to secure stand to smoker base.

Step 4: Tighten Lower Screws

Tighten screws (C) and (D) through stand into smoker body.

Step 5: Leveling with M10 Nut

Use M10 nut (F) as a spacer to level the smoker and enhance stability.

Step 6: Final Assembly

Return assembly upright and re-tighten all hardware.

General Safety Precautions

Use with designated smokers only. Do not sit on or move stand while in use.