To Next PageTo Next PageWhat to do if the light bulb is not working in my Maxxus MX-K306-01 Plumbing Product?
If the light bulb in your Maxxus Plumbing Product is not working, first remove the burned-out light bulb and replace it. If that doesn't solve the problem, check the light bulb wiring to ensure it's not loose; if it is, check the connection and/or replace the lamp assembly. If problems persist, the electrical control panel may need to be replaced.
What to do if my Maxxus Plumbing Product light bulb is not working?
If the light bulb in your Maxxus Plumbing Product is not working, start by checking if the bulb is burned out and replace it if necessary. If the new bulb also doesn't work, the wiring might be loose, so check the connection and replace the lamp assembly if needed. If both of these solutions don't work, the electrical control panel might have issues, and you should replace the relevant control panel.
How to fix Maxxus MX-K306-01 Plumbing Product infrared heater not heating up?
If the infrared heater in your Maxxus Plumbing Product is not heating up, several factors could be the cause. First, the heater itself might be broken, requiring you to replace the heater panel. Also check that the wire junction or the heater’s wire is securely connected. Additionally, a broken temperature sensor can cause this issue, so check its connection. Finally, the circuit board or the relay might not be working, necessitating replacement of the circuit board.
How to resolve 'EP' on the temperature display of my Maxxus MX-K306-01?
If your Maxxus Plumbing Product temperature display shows 'EP', it indicates a problem with the temperature sensor. The connector of the temperature sensor might be loose, not connected, or the sensor itself could be damaged. Try disconnecting and reconnecting the connector of the temperature sensor. If that doesn't work, you may need to replace the temperature sensor with a new one.
Why does my Maxxus MX-K306-01 Plumbing Product CD-Player doesn’t work?
If your Maxxus Plumbing Product CD-Player isn’t working, there are several potential causes. First, check if the power connector is loose or damaged, and disconnect and reconnect the connection. If that doesn't solve the issue, the DC power supply might not be providing power to the CD-player, so check the DC power supply wiring or replace the power supply. The CD-player itself could be defective, requiring replacement. Lastly, check if the CD-player protection fuses are burnt out and replace them if necessary.
What to do if the indicator light for power supply is not working on my Maxxus Plumbing Product?
If the indicator light for the power supply on your Maxxus Plumbing Product is not working, first check the connector to ensure it is properly connected; if not, check the connector or replace it. If the connector is fine, confirm that there is power supply input by checking your circuit breaker to ensure power at the wall outlet. If power is available, the indicator light itself may be broken, requiring you to replace the circuit panel.
What does it mean when the temperature display shows "H" on Maxxus MX-K306-01 Plumbing Product?
If the temperature display of your Maxxus Plumbing Product shows "H", turn off the unit, as the temperature inside the sauna room is too high, and contact the manufacturer.
Why is my Maxxus MX-K306-01 infrared heater not heating up?
If your Maxxus Plumbing Product infrared heater is not heating up, you should check that the wire junction or the heater’s wire is properly connected and tight. If connections are secure, the heater panel, temperature sensor, circuit board, or the relay might be broken, and the circuit board or heater panel may need to be replaced. Also check the connection of the temperature sensor.
How to fix the power supply indicator light not working on Maxxus MX-K306-01?
If the indicator light for the power supply on your Maxxus Plumbing Product is not working, start by checking the connector to ensure it is properly connected; if needed, replace it. Then, verify that there is power at the wall outlet by checking your circuit breaker. If the light still doesn't work, the indicator light itself, the heating indicator light, or the circuit board may be broken, requiring replacement of the circuit board or relevant control panel.
What does it mean when the temperature display shows "H" on my Maxxus MX-K306-01?
If the temperature display on your Maxxus Plumbing Product shows 'H', it means the temperature inside the sauna room is too high. Turn off the unit, and contact the manufacturer.
This document is an instruction manual for Maxxus Infrared Saunas, covering models MX-K206-01, MX-K306-01, MX-K406-01, and MX-M406-01. It provides comprehensive information on assembly, operation, maintenance, and safety for these indoor-use carbon model saunas, available in hemlock and red cedar.
Maxxus Infrared Saunas are designed to provide therapeutic heat using infrared radiant energy, which directly penetrates the body's tissue to induce perspiration. Unlike traditional saunas that heat the air to high temperatures (upwards of 190°F), infrared saunas achieve a similar warming effect at lower temperatures (up to 120°F), making the environment more tolerable and easier to breathe. The process, known as conversion, involves Far Infrared rays penetrating organic substances like the human body two to three inches for a uniform warming effect. The saunas are equipped with carbon heat emitter panels, a control panel for temperature and timer settings, and an MP3 jack or Bluetooth functionality for audio.
General| Product Type | Kitchen Faucet |
|---|---|
| Brand | Maxxus |
| Model Number | MX-K306-01 |
| Finish | Chrome |
| Valve Type | Ceramic Disc |
| Flow Rate | 1.8 GPM |
| Material | Brass |
| Aerator Included | Yes |
| ADA Compliant | Yes |
| Warranty | Limited Lifetime |
| Installation Type | Deck Mounted |
