Why is the Clean Washer LED flashing on my Maytag MED6630HC?
If the Clean Washer LED is flashing at the end of a wash cycle on your Maytag Washer, it's a reminder to run the Clean Washer with affresh® cycle, which is recommended every 30 wash cycles. Run the Clean Washer with affresh® cycle. If you don't, the LED will stop flashing after 3 more regular wash cycles, but will reappear after another 30 cycles as another reminder.
How to fix 'Sd' or 'Sud' error on my Maytag MED6630HC Washer?
If you see "Sd" or "Sud" on your Maytag Washer display, it means there are excessive suds, and the washer is running a suds-reduction routine. Let the washer continue its cycle. Make sure you're only using HE detergent and following the manufacturer’s instructions to determine the correct amount based on load size. Keep in mind that not all HE detergents are the same; some, like natural, organic, or homemade ones, may create more suds. If you're using one of these and see the error code, think about switching to a different HE detergent.
Why won't my Maytag MED6630HC Washer start or fill with water?
If your Maytag Washer won’t run, fill, or stops working, first check the water supply. Ensure both hoses are attached and have water flowing to the inlet valve, and that both hot and cold water faucets are turned on. Also, check that the inlet valve screens aren't clogged and that there are no kinks in the inlet hoses. Verify the electrical supply by plugging the power cord into a grounded 3-prong outlet, avoiding extension cords and GFCI outlets. Confirm there is power to the outlet, and if problems persist, have an electrician check the voltage. Reset any tripped circuit breakers or replace blown fuses.
What to do if my Maytag Washer door won't lock?
If the error code F5 E2 or F05 E02 appears on the display of your Maytag Washer, it means the door will not lock. Touch POWER to cancel the cycle. Make sure that the door is completely closed and latched. Check the washer drum for any items that may be preventing the door from closing completely.
Why is my Maytag Washer not draining properly?
If your Maytag Washer isn't draining or spinning, and loads are still wet, check the drain hose installation. Ensure it doesn't extend more than 4.5" (114 mm) into the standpipe. Use the drain hose form to securely attach it to the drainpipe or tub, without taping over the drain opening. Also, make sure the drain hose isn't clogged or higher than 96" (2.4 m) above the floor. Remove any clogs, and ensure the hose fits loosely but securely in the standpipe, without being sealed with tape to allow for an air gap. Also, remove any strainer/nylon stocking on end of drain hose.
Why is my Maytag Washer leaking around the door?
If you notice leaking around the door of your Maytag Washer, it could be due to hair, lint, or other debris on the inner door glass, preventing a proper seal with the rubber door seal. Clean the inner door glass and seal. See “Cleaning the Door Seal” in the “Washer Maintenance” section.
Why does my Maytag Washer beep when I press start?
If your Maytag Washer beeps when START is touched, it means the door is not closed completely. Close the door completely.
Why is my Maytag MED6630HC Washer load not completely covered in water?
If the load in your Maytag Washer is not completely covered in water, it is normal for an HE front-load washer. The washer senses load sizes and adds the correct amount of water for optimal cleaning.
What does 'rL' mean on my Maytag Washer?
If "rL" appears on the display of your Maytag Washer, it means a load was detected in the drum during the Clean Washer with affresh® cycle. Remove the items from the washer drum and restart the Clean Washer with affresh® cycle.
How do I fix 'Lo FL' error on my Maytag MED6630HC?
If you see 'Lo FL' or 'F8 E1' or 'F08 E01' on your Maytag Washer display, it indicates a water supply error. The unit will drain for 8 minutes with the door locked, and this drain cycle must complete to reset the error. Touch POWER once to clear the code, then again to restart the washer. If the code reappears, call for service. Also, make sure both hoses are attached and have water flowing to the inlet valve, and that both hot and cold water faucets are turned ON. Check the inlet valve screens on the washer to ensure they are not clogged. Remove any kinks in the inlet hose. If used, auto shut-off connectors and hoses must be properly installed and in working order.
Lists necessary and optional tools, and parts supplied/needed.
Essential safety guidelines for properly grounding the appliance.
Instructions for safely moving the washer to its installation location.
Details on connecting the hot and cold water hoses to the respective faucets.
Detailed instructions on how to adjust the washer's feet to achieve a level position.
General| Fuel Type | Electric |
|---|---|
| Color | Chrome Shadow |
| Brand | Maytag |
| Model | MED6630HC |
| Depth | 30.5 inches |
| Steam Cycle | Yes |
| Wrinkle Prevent Option | Yes |
| Type | Front Load |
| Energy Star Certified | Yes |
| Frequency | 60 Hz |
| Width | 27 inch |
| Voltage | 240 V |
To Next Page
