McCulloch ROB S500 User Manual

56 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

EN, English

Operator's manual

ROB S400, ROB S500,

ROB S600

Read the operator's manual carefully and make sure that you

understand the instructions before you use the product.

Table of Contents

Other manuals for McCulloch ROB S500

Quick Guide4 pages

Questions and Answers:

F
Frederick HernandezAug 21, 2025
How to fix no loop signal on McCulloch ROB S500?
- W
  Wayne BeasleyAug 21, 2025
  If your McCulloch Lawn Mower displays a 'No loop signal' error, several issues could be the cause. First, verify the power supply is correctly connected to the wall socket and that the low voltage cable is undamaged and properly connected to the charging station. Check the boundary wire connections to the charging station and inspect the boundary wire for any breaks, replacing any damaged sections. Ensure ECO mode is not activated while the mower is outside the charging station. Also, confirm the boundary wire isn't crossed, especially around any islands, and if the signal is broken, place the product in the charging station and generate a new loop signal.
J
Jessica ReedAug 23, 2025
What to do if McCulloch ROB S500 battery is empty?
- E
  Elizabeth FullerAug 23, 2025
  If your McCulloch Lawn Mower shows an empty battery, make sure the charging station and guide wire are correctly installed. Check if the guide wire is broken or not properly connected. If these steps don't resolve the issue, the battery might be spent and require replacement. Also, check if the indicator lamp in the charging station flashes red, which could indicate a defective charging station antenna.
P
Patricia NicholsonAug 25, 2025
Why McCulloch Lawn Mower is not driving?
- B
  berrymichaelAug 25, 2025
  If your McCulloch Lawn Mower isn't driving, it might be caught on something; free it and address the cause. If wet grass is the issue, wait for the lawn to dry. For work areas with steep slopes, these areas should be isolated. If a guide wire is on a slope, ensure it is laid at an angle across the slope.
B
Breanna WoodwardAug 27, 2025
What to do if McCulloch ROB S500 Lawn Mower cutting system is blocked?
- M
  Mary NorrisAug 27, 2025
  If the cutting system of your McCulloch Lawn Mower is blocked, it might be due to grass or another object wrapped around the blade disc; inspect and remove any obstructions. Also, ensure the blade disc isn't sitting in a pool of water; relocate the product and prevent water accumulation. Finally, if the grass is too high, cut it before using the product, ensuring it's no more than 4 cm / 1.6 in.
M
Melissa CollierAug 27, 2025
Why McCulloch ROB S500 Lawn Mower is outside working area?
- B
  Benjamin EdwardsAug 27, 2025
  If your McCulloch Lawn Mower is operating outside the designated working area, the boundary wire connections to the charging station may be crossed; ensure they are correctly connected. Check that the boundary wire is laid according to the provided instructions and isn't too close to the work area's edge. Interference from metal objects or buried cables nearby could also be a factor, so try moving the boundary wire. If another product installation is nearby, place your product in the charging station and generate a new loop signal.
S
Steven WhiteAug 29, 2025
What to do if McCulloch ROB S500 Lawn Mower wheel motor is blocked?
- J
  jbruceAug 29, 2025
  If the wheel motor on your McCulloch Lawn Mower is blocked, check the drive wheel for grass or other objects wrapped around it and remove any obstructions.
M
mcintyreadamAug 30, 2025
What to do if McCulloch Lawn Mower is trapped?
- M
  Michael FergusonAug 31, 2025
  If your McCulloch Lawn Mower is trapped, free it and identify what caused it to get stuck. If it's stuck behind multiple obstacles, assess the area and remove any obstructions or create an island around them to allow free movement.
P
pamela88Sep 1, 2025
Why McCulloch ROB S500 Lawn Mower is stuck in charging station?
- S
  Scott WangSep 1, 2025
  If your McCulloch Lawn Mower is stuck in the charging station, there may be an object preventing it from leaving. Remove the object to allow the product to move freely.
J
Jessica RoachSep 2, 2025
What to do if McCulloch ROB S500 is lifted?
- M
  Melissa ElliottSep 2, 2025
  If your McCulloch Lawn Mower displays a 'Lifted' message, it means the lift sensor has been activated. Ensure the product body can move freely around its chassis. Remove any objects that may cause the chassis to lift or create an island around such objects.
J
Joshua MorrisSep 4, 2025
How to resolve guide not found error on McCulloch ROB S500?
- B
  Bonnie WestSep 4, 2025
  If your McCulloch Lawn Mower displays a 'Guide not found' error, ensure the guide wire connector is tightly connected to the charging station. Check for any breaks in the guide wire, and if found, replace the damaged section. Also, verify that the guide wire is correctly connected to the boundary loop.

McCulloch ROB S500 Specifications

General

Type	Robotic Lawn Mower
Maximum Area	500 m²
Battery Type	Lithium-Ion
Battery Voltage	18 V
Cutting Height	20-50 mm
Maximum Slope	25%
Typical mowing time on one charge	65 min
Battery capacity	2.1 Ah
Engine Type	Electric
Cutting Height Adjustment	Manual

Summary

2 Safety

2.1 Important Safety Precautions

Critical safety warnings and precautions to read before operating.

2.2 Safety Definitions and Operational Safety

Defines safety terms and provides instructions for safe operation.

2.3.2 Battery Safety and Product Handling

Safety guidelines for battery handling, lifting, and moving the product.

2.3.4 Maintenance and Environmental Safety

3 Installation

3.1 Installation Introduction and Preparations

3.4 Wire Placement and Installation Planning

Details planning for boundary and guide wire placement, and examining locations.

3.5 Product Installation and Wire Connection

Instructions for installing the charging station, boundary, and guide wires.

3.9 Post-Installation Checks and Settings

3.10 Product Settings and Configuration

4 Operation

4.1 Product Controls and Starting

Explains the ON/OFF button, indicator lamp, and how to start the product.

4.3 Operating Modes and Park Modes

4.7 Schedule, Standby, and Charging

5 Maintenance

5.1 Introduction and General Cleaning

5.3 Blade Replacement and Battery Care

6 Troubleshooting

6.1 Introduction and Fault Messages

Introduction to troubleshooting and a guide to fault messages.

6.3 Information Messages and Indicator Lamps

Explains information messages and indicator lamp status for troubleshooting.

6.5 Symptoms and Wire Troubleshooting

9 Warranty

9.1 Warranty Terms and Conditions

Related product manuals

Preview: McCulloch ROB S600

McCulloch ROB S600

McCulloch ROB S800

Preview: McCulloch ROB S400

McCulloch ROB S400

Preview: McCulloch ROB R600

McCulloch ROB R600

Preview: McCulloch ROB R800

McCulloch ROB R800

McCulloch ROB R1000

McCulloch Edition 1-R

McCulloch M51-650 CMDW-R

McCulloch M53-875 CMDW-R

McCulloch M53-675 CMDW-R

Preview: McCulloch 532 43 18-99 Rev. 1

McCulloch 532 43 18-99 Rev. 1

McCulloch 532 43 37-12 Rev. 1