McIntosh MC7205 THX User Manual

7
How to Connect the MC7205
To AC
Outlet
How to Connect the MC7205
123456789
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
123456789
123456789
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
123456789
123456789
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
123456789
123456789
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
123456789
123456789
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
1
2345678
9
123456789
Front
Right
Speaker
Surround
Left
Speaker
Surround
Right
Speaker
Front
Left
Speaker
Front
Center
Speaker
McIntosh SL-1 Power Sub-Woofer
1. Connect the MC7205 power cord to a live AC outlet.
2. Prepare the loudspeaker hookup cables as follows:
A. Carefully remove sufficient insulation from the
loudspeaker cable ends to just fit within the bind-
ing post with no exposed wire accessible. Refer to
figure 1.
B. If the cable is stranded, carefully twist the strands
together as tightly as possible. Refer to figures 2 &
3.
Note: If desired, the twisted
cable section can be
tinned with a solder iron
to keep the strands
together and/or attach
appropriate connector
ends.
C. Insert the bare section of the
cable end or connector into
the access hole, and tighten
the terminal nut clockwise
until the cable is firmly
clamped into the terminal so
the wires cannot slip out. Refer to figure 4.
D. Insert the bare section of the cable end or connector
into the access hole, and tighten the terminal nut
clockwise until the cable is firmly clamped into the
terminal. Refer to figures 5 & 6.
Note: The bare sections of the cable ends or the non
insulated part of the connectors must not be exposed on
either side of the terminal access hole.
E. Repeats Steps A through D for each speaker cable
used with the amplifier.
3. Connect the loudspeaker cables to the
appropriate output connectors, being
careful to observe the correct polari-
ties and install the protective covers
that were supplied. Refer to figure 7.
4. Connect a single DB25 computer type
cable from the multi-channel output
of a control center to the THX Input
connector for all six audio channels
and power control.
5. Connect the MC7205 Sub In/Out to the McIntosh SL-1
Subwoofer THX input and a power control cable from
the MC7205 Power Control Out to the SL-1 Power
Control In.
Note: An optional hookup is to use discrete cables from a
McIntosh Control Center to inputs of the MC7205.
Connect a Y adapter to the Control Center
Subwoofer Output, with one cable to the SL-1
subwoofer THX input and a second cable to the
MC7205 Sub In/Out jack. Connect a power control
cable from the Control Center Power Control Out to the
MC7205 power control in jack and connect a power
control cable from the MC7205 Power Control Out to
the SL-1 Power Control In.
McIntosh MX132 A/V Control Center
Figure 7

McIntosh MC7205 THX Specifications

General

Brand	McIntosh
Model	MC7205 THX
Category	Amplifier
Language	English