EasyManuals Logo

Melitta LOOK Perfection User Manual

Melitta LOOK Perfection
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #7 background imageLoading...
Page #7 background image
9
not be carried out by children,
unless they are 8 years or older
and are supervised. Keep the
appliance and the power cable
away from children under 8 years
of age.
•Theappliancemaybeusedby
persons with reduced physical,
sensory or mental abilities or
lack of experience and/or know-
ledge if they are supervised or
have been instructed in the safe
use of the appliance and have
understood the potential hazards.
•Childrenmustnotplaywiththe
appliance
•Replacementofthepowercable
and all other repairs may only be
carried out by Melitta
®
Custo-
mer Service or by an authorised
repair shop.
2. Before rst use
•Ensurethatthepowersupplyinyourhomecorres-
ponds to that on the model plate on the base of the
appliance.
•Placetheapplianceonadry,levelandstablesurface.
•Connecttheappliancetoapowersource.Unused
cable can be stored in the base of the appliance .
•Allapplianceshavebeentestedduringproduction
for perfect functioning. Therefore there may be
for example water deposits remaining. Rinse the
appliance twice with the maximum amount of water
and without a filter bag or ground coee, in order to
clean it.
•Forthebestcoeeenjoymentandconvenientuse,
the appliance is equipped with various features.
These features are explained below.
3. Set water hardness
Depending on water hardness lime scale may build up
in the appliance. This increases the appliances energy
consumption as lime scale on the heating element can
prevent the water heating eectively. To avoid damage
the appliance must be descaled regularly. The descaling
display helps you in this. If the CALC button is
permanently lit this shows that the appliance needs to
be descaled.
The appliance is pre-set for a high level of water
hardness (level 4). You can find out the level of water
hardness in your area by asking your local water
provider or by using water hardness measuring strips
available in the shops. For softer water the descaling
display can be adjusted to descale less often:
•HolddowntheCALCbutton for longer than 2
seconds. The CALC button starts to flash. In the
factory settings the CALC button flashes briefly four
times with the following pauses ………
•Youcansetthewaterhardnessatthreefurther
levels. Each time you briefly press the CALC button
the display changes to flashing one, two or three
times, each time followed by a pause
(……, ……, ……).
•Thesettingsanddisplayareshowninthefollowing
table 1.
•Onceyouhavesetthedesiredhardnesslevel,again
hold the CALC button down for longer than two
seconds. The light goes o and your settings are
saved.
Please note:
•Waterhardnesscannotbeprogrammedwhile
brewing.
•Thelastwaterhardnesslevelchosenremainseven
after removing the power cable.
4. Setting the hotplate
Keeping coee warm on the hotplate aects the taste
of your coee. To avoid this you should enjoy your
coee fresh by drinking it as soon after brewing as
possible. Unnecessary warming also uses valuable
energy. The factory settings for the appliance are for
40 minutes of warming. After this the hotplate turns
o automatically. This time can be changed as needed:
•PresstheON/OFFbutton longer than two seconds.
•InthefactorysettingstheON/OFFbutton flashes
briefly twice with the following pause (……).
•Therearetwoothersettingsforthewarmingtime.
By briefly pressing the ON/OFF button the
display changes to flashing three times or once, each
time followed by a pause (……, ……, ……).
•Thesettingsanddisplayareshownintable2.
•Onceyouhavesetthedesiredwarmingtime,
confirm your settings by pressing the ON/OFF
button for longer than two seconds. Your settings
are now saved
•Thelastsettingchosenremainsevenafterremoving
the power cable.
5. Making coffee
•Ensurethattheapplianceisconnectedtothepower
source.
•Fillthewatertank.
•Removethedetachablewatertankbyholdingthe
recessed grip and pulling straight up .
•Removethewatertanklidandllwiththedesired
amount of fresh water from the tap. Using the water
level indicator on the tank you an choose the cor-
rect number of cups.
•Closethetankbyreplacingthelidandinsertthe
tank back in the appliance. Please ensure that you
replace the tank upright in the appliance. The guide
rails on the appliance (left of the tank) will help you
with this .
•Alternativelyusetheglassjugtopourthewaterinto
the tank in the appliance . The required amount
of water can be seen on the water level indicator on
the tank.
Small cup symbol = approx. 85 ml coee per cup,
 G B

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Melitta LOOK Perfection and is the answer not in the manual?

Melitta LOOK Perfection Specifications

General IconGeneral
Jug capacity1.25 L
Product typeDrip coffee maker
Built-in grinderNo
Capacity in cups15 cups
Hot water system-
Number of spouts1
Coffee input typeGround coffee
Coffee maker typeFully-auto
Appliance placementCountertop
Adjustable coffee strengthYes
Reservoir for brewed coffeeJug
Control typeButtons
Product colorBlack, Silver
Package depth260 mm
Package width255 mm
Package height366 mm
Package weight3150 g
Weight and Dimensions IconWeight and Dimensions
Depth230 mm
Width232 mm
Height325 mm

Related product manuals