EasyManuals Logo

Meyer Sound DS-2P User Manual

Meyer Sound DS-2P
14 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
3
Contents
Controls and Connectors
European User Panel with
IEC 309 connector
Dimensions
Front Side Top
All units in inches
UU
LL
CC
UU
LL
®®
LISTED
3K59
COMMERCIAL
AUDIO SYSTEM
ATENCIÓN
:
ACCESO INTERNO
A PERSONAL TÉCNICO CALIFICA
ACHTUNG
:
GEHÄUSE NICH
WARTUNG UND REPARATUR
ELEKTROFACHKRÄFTE
ATTENTION
:
ENTRETIEN E
INTERNES NE SONT AUTORISEE
TECHNIQUE QUALIFIÉ
UK WARNING
:
THIS APPARAT
NO OPERATOR SERVICEABLE PART
SERVICING TO QUALIFIED PERSONN
WARNINGS:
This surface may reach high tempera
To ensure proper operation, allow a
clearance from this surface and adeq
To reduce the risk of electric shoc
No operator serviceable parts insid
qualified personnel.
To reduce the risk of fire or electric
this appliance to rain or moisture.
P
U
S
H
R
E
-
C
I
R
K
-
I
T
Earth / Chassis
Earth / Chassis
Input
Loop
Pin
2 +
3 +
!
1
1
2
3
1
3
2
8A RMS
20A Peak
95-125
~
50-60Hz
700W RMS MAX
Meyer Sound,
Auto-Voltage Sele
Input Polarity
THIS PRODUCT MUST BE GROUNDED
P
U
S
H
R
E
-
C
I
R
K
-
I
T
PUSH
Made by:Meyer Sound,Berkeley,Ca. U.S.A.
European Office:
Meyer Sound Europe
14, Long Barn Lane,
Reading, Berkshire,
England RG2 7SZ
Controls and Connectors .................................. 3
Dimensions ........................................................ 3
Introduction ....................................................... 4
AC Power ........................................................... 4
Audio Input ........................................................ 6
Amplification and Protection Circuitry ............ 6
Rigging ............................................................... 8
Measurement and System Integration Tools ....... 8
Complete Systems ..................................................9
Driver Troubleshooting.........................................10
Array Design ..........................................................12
Safety Summary....................................................13
Specifications ........................................................14
ATENCIÓN
:
ACCESO INTERNO SOLO
AUTORIZADO A PERSONAL TÉCNICO CALIFICADO
ACHTUNG
:
GEHÄUSE NICHT ÖFFNEN WARTUNG
UND REPARATUR NUR DURCH ELEKTROFACHKRÄFTE
ATTENTION
:
ENTRETIEN ET REPARATIONS
INTERNES NE SONT AUTORISEES QU'AU
PERSONNEL TECHNIQUE QUALIFIÉ
UK WARNING
:
THIS APPARATUS MUST BE EARTHED.
NO OPERATOR SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL
WARNINGS:
THIS PRODUCT MUST BE GROUNDED
This surface may reach high temperatures while in use.
To ensure proper operation, allow at least 6 inches
clearance from this surface and adequate ventilation.
To reduce the risk of electric shock do not remove cover.
No operator serviceable parts inside.
Refer servicing to qualified personnel.
To reduce the risk of fire or electric shock
do not expose this appliance to rain or moisture.
!
Meyer Sound, Berkeley, CA. USA
1
2
3
1
3
2
Loop
Input
PUSH
Active / Speaker Fault
2 +
3 +
10K
Balanced
Input Polarity
Network
Service
Wink
Reset
Activity
Remote Monitoring System
Earth / Chassis
1
Case
220K
ESD
P
U
S
H
R
E
-
C
I
R
K
-
I
T
P
U
S
H
R
E
-
C
I
R
K
-
I
T
Mains circuit
breakers
Signal input and
loop connectors
Power LED (green/red)
Input polarity switch
Tie-wrap anch
o
Mains AC inlet
Remote Monitoring
System panel
(if RMS is installed)
LO Limit
Driver Excursion Clamp
Low Limit (red)
Exc. Clamp
DS-2P
95-125V
~
50-60Hz
1400W RMS MAX
208-235V
~
50-60Hz
1400W RMS MAX
Auto-Voltage Select
Rear User Panel shown with the optional
Remote Monitoring System (RMS) panel
56.75
14.25
28.75
5.50
30.00
21.25
7.5°
30.26
13.16
21.97
30.00
13.36

Other manuals for Meyer Sound DS-2P

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Meyer Sound DS-2P and is the answer not in the manual?

Meyer Sound DS-2P Specifications

Acoustical IconAcoustical
frequency response± 4 dB 50 – 160 Hz
phase response± 60° 60 – 200 Hz
maximum SPL (music as source)140 peak
maximum SPL (pink noise as source)136 dB continuous; 140 peak
dynamic range> 120 dB
coverage120° H x 120° V
Transducers IconTransducers
low frequency transducerTwo 15" diameter MS-15 cone
Audio Input IconAudio Input
input type impedance10 kΩ
connectorXLR (A-3) male and female
nominal input level+4 dBu (1.23 Vrms)
Amplifiers IconAmplifiers
amplifier typeComplementary power MOSFET output stages class AB/H
burst capability1240 Watts (620 Watts per channel)
THD, IM, TIM< .02 %
AC Power IconAC Power
connector250 V NEMA L6-20P / IEC 309 Twistlock male receptacle
automatic voltage selection85 – 134 V / 165 – 264 V; 50 Hz / 60 Hz
max continuous RMS current (115 V)8 A
max continuous RMS current (230 V)4 A
max continuous RMS current (100 V)10 A
max burst RMS current (115 V)15 A
max burst RMS current (230 V)8 A
max burst RMS current (100 V)18 A
max peak current during burst (115 V)22 Apk
max peak current during burst (230 V)11 Apk
max peak current during burst (100 V)25 Apk
soft-current turn-on inrush current< 12A @115V
Physical IconPhysical
dimensions21.25” W x 56.75” H x 30” D
weight221 lb (100 kg)
shipping weight267 lb (121 kg)

Related product manuals