Miccus Home RTX 2.0 - Miccus RTX 2.0 Quick Start Guide; Antenna Setup; Connecting Audio Sources; Powering Device On and Off

Quick Start Guide:
1. Aachtheantenna:on the back of the Miccus® Home RTX 2.0,
remove the white rubber connector cover and aach the supplied
antenna to the antenna terminal (turn clockwise unl slightly snug).
Opmize antenna performance by posioning the antenna upright.
2. ConnecngtotheMiccus®HomeRTX2.0:Connect the appropri-
ate included cable (Opcal/TOSLINK or RCA to 3.5mm) to the
appropriate audio input (TX mode only) or output (RX mode only)
on the back of the RTX 2.0.
3. Poweron/o:Before connecng to power, set the selector switch
to TX (transmit mode), or RX (receive mode). The Miccus® Home
RTX 2.0 can be operated using any USB port or 5v/500mA USB
power supply. Connect the micro end of the USB cable to the
RTX 2.0 and the other end to USB power; the Home RTX 2.0 will
automacally power on. If powered o, the Home RTX 2.0 can be
powered back on by holding the mul-funcon/power buon
for 5 seconds unl the LED indicators power on.
4. Paring: Place your Bluetooth® receiving or transming device
into pairing mode; follow the manufacturer specic instrucons.
Then press and hold the Home RTX 2.0 mul-funcon/ power
buon for 3 seconds unl a channel (CH) indicator light begins
fast ashing. This indicates pairing mode. Once paired the
appropriate CH indicator LED will light solid and blink every
5 seconds in accordance with the codec being used. Note: if
your phone or tablet requires a passkey for pairing use: 0000
5. Dual-Link Pairing: Dual link pairing allows for two Bluetooth®
receiving devices to pair with the Miccus® Home RTX 2.0
simultaneously. Once you’ve paired your rst set of headphones
to the Miccus® Home RTX 2.0 (step 4 above), to pair a second
set of headphones, press and hold the RTX 2.0 mul-funcon/
power buon for 3 seconds unl the CH indicator light begins fast
ashing. Once the second set of headphones is paired, both CH
indicator lights will be solid or blink every 5 seconds in accordance
with the codec being used.
1
Note: The Home RTX 2.0 can transmit dual audio streams using the
aptX Low Latency codec. The Home RTX 2.0 automacally recognizes an
audio feed as either digital opcal, or 3.5mm analog according to the
cable connected.
CH1 or CH2 LED SOLID BLUE RTX 2.0 connected with
SBC or aptX codecs
CH1 or CH2 LED blue 2 blinks
every 5 seconds
RTX 2.0 connected with
aptX Low Latency codec
For detailed instrucons and troubleshoong please connue reading
the Miccus® Home RTX 2.0 user manual or visit www.miccus.com for
how-to videos.
AbouttheMiccus®HomeRTX2.0
The Miccus® Home RTX 2.0 is the rst dual link long range
wireless transmier or receiver featuring Bluetooth® v4.2 and
two simultaneous aptX Low Latency audio streams. Use as either a
Bluetooth® receiver or transmier and add Bluetooth® technology
to your exisng television or stereo equipment. The Home RTX 2.0
supports dual link pairing; which means two devices can be paired at the
same me. The Miccus® Home RTX 2.0 also features opcal audio pass
thru. Use the same audio source and daisy chain two or more Miccus®
Home RTX 2.0’s together; double or even triple the number of low latency
audio streams available for use. Avoid the use of an opcal splier box;
use the digital audio pass thru of the Home RTX 2.0 to send television
audio to both the RTX 2.0 and your soundbar.
What’sintheBox?
2
A. Miccus® Home RTX 2.0
B. Dipole Antenna
C. Opcal / TOSLINK digital
audio cable
D. 3.5mm male to 3.5mm
male Audio Cable
E. Micro USB charging cable
F. USB Power Supply
G. User Manual