How to fix a banging noise in my Miele Medical Equipment?
If you hear a banging noise in the wash cabinet of your Miele Medical Equipment, it means a wash arm is hitting the items. Interrupt the program and re-arrange any items that are blocking the wash arm.
What to do if the "Fill/Drain" light flashes on my Miele Medical Equipment?
If the "Fill/Drain" indicator light flashes and the program stops a few minutes after starting on your Miele Medical Equipment, it indicates a problem with the water inflow, producing error message F..E. Ensure that the water valve is completely open and clean the filter in the water inlet. If the flow pressure at the water connection is too low, contact a qualified plumber for advice.
What does it mean when the "Fill/Drain" light is flashing during the rinse program on my Miele Medical Equipment?
If the rinse program is interrupted and the "Fill/Drain" indicator light is flashing on your Miele Medical Equipment, producing error message F..A, it means there is a problem with the water outflow. To solve this, clean the filter combination in the wash cabinet, the drain pump, and the non-return valve. Also, check the drain hose for any kinks and remove them.
How to remove white spots from my Miele Medical Equipment?
If you notice white deposits and/or spots on items washed in your Miele Medical Equipment, several factors could be responsible: * The water softener setting may be too low. Test the tap water hardness and program the water softener accordingly. * There might be no reactivation salt in the reservoir. Carefully fill the reservoir with reactivation salt. * The screw cap on the reservoir might not be firmly tightened. Ensure the cap is properly threaded and tightened. * The rinse aid setting could be too low, leading to water spots. Increase the rinse aid dosage. * There may be dental cement residue on the items. Remove cement residue from items before it hardens.
Why isn't the water getting hot in my Miele Medical Equipment?
If the water in the wash cabinet of your Miele Medical Equipment isn't getting hot and the program is taking too long, producing error messages F01 - F03, F18, F19, it could be due to the temperature sensor switching off the heater because of overheating. To resolve this, identify and remove the underlying cause by cleaning the filter combination in the wash cabinet, rearranging the items, and resetting the temperature sensor.
Why are items corroding in my Miele Medical Equipment?
If items washed in your Miele Medical Equipment show signs of corrosion, it could be due to a couple of reasons: * The items may not be washer-safe. Ensure only undamaged items made of surgical stainless steel are placed in the washer-disinfector. * Neutralization may not have occurred during the program sequence. Make sure to fill the neutralizer container.
Why is the wash result unacceptable with my Miele Medical Equipment?
If you find the wash result unacceptable with your Miele Medical Equipment, consider the following possible causes: 1. The baskets and inserts may have been incorrectly loaded or overfull. Properly arrange the items and avoid overloading. 2. The detergent used might not be suitable for the type or amount of soiling. Use a detergent specifically designed for machine washing. 3. The items may have been left soiled for too long. Do not leave soiled items unwashed for more than 6 hours. 4. A spray arm could be blocked. Ensure that the spray arms are not obstructed by the items. 5. Nozzles may be blocked in the spray arms or inserts. Check and clean the spray nozzles as needed. 6. The wash cabinet filters may be dirty. Inspect and clean the filters as necessary. 7. The basket or insert ...
Why is my Miele Medical Equipment making a rattling noise?
If you hear a rattling noise in the wash cabinet of your Miele Medical Equipment, it indicates that items are moving around inside. Interrupt the program and re-arrange any loose items.
What does it mean when the "Recharge" light is flashing on my Miele Medical Equipment?
If the refill salt message "Recharge" is flashing on your Miele Medical Equipment, it means the water softener could not be reactivated because no regeneration salt was added. Carefully fill the reservoir with reactivation salt.
What to do when the neutralizer light flashes and the program stops on my Miele Medical Equipment?
If, a few minutes after the start of a program, the "Neutralizer" indicator light flashes and the program stops on your Miele Medical Equipment, producing error message Fdo, it indicates a problem dispensing the neutralizer. Refill or replace the neutralizer container and prime the dosage system.
Guidelines for safe operation and intended use of the machine.
Critical safety instructions to avoid personal injury during operation.
Essential steps to follow before operating the machine for the first time.
Detailed steps to set the water softener to the local water hardness.
Steps for powering on, selecting, and initiating wash programs.
Procedures for regular maintenance, testing, and routine checks.
Identifying and resolving issues like the machine not starting or being ready.
Steps for positioning, securing, and installing the washer-disinfector.
Instructions for making the electrical connection according to safety regulations.
Instructions for connecting the water supply and drain.
To Next Page
General
