Need help?Do you have a question about the Miele G 7882 and is the answer not in the manual?
General| Appliance type | Washer |
|---|---|
| Type | Front-loading |
| Spin speed | 1600 rpm |
| Width | 60 cm |
| Height | 85 cm |
| Programs | Cotton |
Identifies and explains the various control buttons, display, and indicators on the machine.
Identifies and describes the main external and internal components of the washer-disinfector.
Defines intended use, application, and highlights crucial safety notes like earthing and explosion risks.
Covers personnel training, handling chemicals, and safety during machine operation (hot surfaces, etc.).
Emphasizes safe program execution, agent use, and confirmation of disinfection standards.
Warns against solvents, acids, and covers safe accessory use and old machine disposal.
Provides guidance on recycling packaging and environmentally friendly disposal of the old appliance.
Covers setting the water softener, adding rinsing agent, and initial machine loading.
Explains the electric door lock, opening/closing, and cancelling a programme in emergencies.
Details the procedure for opening the door in case of a power failure or emergency.
Explains the need for water softening and how to set the unit based on local water hardness.
Presents a chart correlating water hardness (°d, mmol/l, °f) with the required machine setting.
Step-by-step instructions for programming the water softener unit via the control panel.
Detailed instructions on how to correctly fill the salt reservoir with reactivation salt.
Explains the salt indicator light and the reactivation process.
Explains rinsing agent function, filling reservoir, and indicator lights.
Guides on adjusting the rinsing agent dosage for optimal drying results.
Explains the use of neutralising agent and its automatic dispensing during specific cycles.
Explains when and how to add chemical disinfecting agent, requiring a specific module.
Recommends detergent types, explains dispenser use, and provides dosage info.
Discusses agent selection impacts and maintenance for the dispensing system.
Provides advice on arranging items for optimal water contact and material compatibility.
Explains door ajar for drying and specific advice for loading instruments like endoscopes.
Illustrates loading examples using specific baskets for various instruments.
Shows loading examples using baskets for endoscopes and funnels.
Explains how to adjust the height of the top basket to accommodate different item sizes.
Details programmes like A, B, UNIVERSAL, CHEM with usage and agent info.
Shows the sequence of operations (Pre-wash, Rinse, Final rinse) for different programmes.
Describes SPECIAL AN, SPECIAL, varioTD programmes with usage and agent info.
Continues the programme sequence details for various programmes.
Step-by-step guide to powering on the washer-disinfector and initiating a wash programme.
Covers changing programmes, selecting additional functions, and turning off the machine.
Detailed steps to cancel a running programme, including special procedures for epidemic control.
Setting dosage concentration and venting for liquid cleaning agent via DOS module.
Procedures for venting the liquid cleaning agent dispensing system.
Setting dosage concentration and venting for neutralising agent.
Setting dosage concentration and venting for chemical disinfecting agent.
Adjusting main wash and final rinse temperatures and holding times.
Modifying final rinse temperature and holding time.
Configuring buzzer for programme end, fault indication, or test item removal.
Restoring all parameter changes back to original factory defaults.
Instructions for cleaning coarse, fine, flat, and micro-fine filters in the wash cabinet.
How to remove and clean the upper, middle, and lower spray arms.
Steps to clean the drain pump and non-return valve if blockages occur.
How to clean water inlet filters and the control/front panels.
Troubleshooting issues like machine not starting or wash cycle finishing early.
Resolving water heating issues and guidance on contacting after-sales service for persistent faults.
Details installation methods, levelling, and steam condenser safety.
Guidance on machine placement, securing, and optional cover plates/panels.
Covers electrical safety, earthing, bonding, and steps to remove the service panel.
Instructions for refitting the service panel and related components after electrical work.
Requirements for connecting to water supply, pressure, stopcocks, and AD water.
Specific pressure requirements for AD water connection and potential reprogramming.
Guidelines for connecting the drainage system, including height and flow rate requirements.
To Next Page
