Miele G 7881 User Manual (English)

Other manuals for Miele G 7881

Installation And Operating Instructions76 pages

Questions and Answers:

E
emilyodonnellAug 21, 2025
Why won't my Miele Medical Equipment washer-disinfector start?
- K
  Kelsey JamesAug 21, 2025
  If your Miele Medical Equipment washer-disinfector won't start, there are several potential causes: * The door may not be properly closed. Ensure that you close the door firmly. * The machine might not be plugged in. Check the power cord and plug it in. * A fuse could be blown or the circuit breaker tripped. Reset the fuse, referring to the rating plate for minimum fuse ratings. * The machine may not be turned on. Press the "ON/OFF" button and select a program.
S
shannon61Aug 22, 2025
What to do if the "Fill/Drain" light flashes on my Miele Medical Equipment?
- J
  Justin JohnsonAug 22, 2025
  If the "Fill/Drain" indicator light flashes and the program stops a few minutes after starting on your Miele Medical Equipment, it indicates a problem with the water inflow, producing error message F..E. Ensure that the water valve is completely open and clean the filter in the water inlet. If the flow pressure at the water connection is too low, contact a qualified plumber for advice.
J
Jason RyanAug 25, 2025
What does it mean when the "Fill/Drain" light is flashing during the rinse program on my Miele Medical Equipment?
- B
  bwarnerAug 25, 2025
  If the rinse program is interrupted and the "Fill/Drain" indicator light is flashing on your Miele Medical Equipment, producing error message F..A, it means there is a problem with the water outflow. To solve this, clean the filter combination in the wash cabinet, the drain pump, and the non-return valve. Also, check the drain hose for any kinks and remove them.
A
Anna PettyAug 27, 2025
How to remove white spots from my Miele Medical Equipment?
- A
  anelsonAug 28, 2025
  If you notice white deposits and/or spots on items washed in your Miele Medical Equipment, several factors could be responsible: * The water softener setting may be too low. Test the tap water hardness and program the water softener accordingly. * There might be no reactivation salt in the reservoir. Carefully fill the reservoir with reactivation salt. * The screw cap on the reservoir might not be firmly tightened. Ensure the cap is properly threaded and tightened. * The rinse aid setting could be too low, leading to water spots. Increase the rinse aid dosage. * There may be dental cement residue on the items. Remove cement residue from items before it hardens.
S
Sarah FlynnAug 29, 2025
Why isn't the water getting hot in my Miele Medical Equipment?
- H
  henryruizAug 29, 2025
  If the water in the wash cabinet of your Miele Medical Equipment isn't getting hot and the program is taking too long, producing error messages F01 - F03, F18, F19, it could be due to the temperature sensor switching off the heater because of overheating. To resolve this, identify and remove the underlying cause by cleaning the filter combination in the wash cabinet, rearranging the items, and resetting the temperature sensor.
J
Jenna StoneAug 31, 2025
Why are items corroding in my Miele Medical Equipment?
- B
  Benjamin CopelandAug 31, 2025
  If items washed in your Miele Medical Equipment show signs of corrosion, it could be due to a couple of reasons: * The items may not be washer-safe. Ensure only undamaged items made of surgical stainless steel are placed in the washer-disinfector. * Neutralization may not have occurred during the program sequence. Make sure to fill the neutralizer container.
J
Judy BerrySep 1, 2025
What to do if detergent light flashes and program stops on Miele Medical Equipment?
- M
  Martin MurphySep 2, 2025
  If, a few minutes after starting a program, the Detergent indicator light flashes and the program stops on your Miele Medical Equipment, producing error message Fdo, it indicates a problem dispensing the liquid detergent. Refill or replace the liquid detergent container and prime the dosage system.
M
Melissa RodriguezSep 3, 2025
Why does the detergent light flash on my Miele Medical Equipment before the program starts?
- O
  owenvanessaSep 3, 2025
  If the Detergent indicator light flashes before the start of a program and the program can't be started on your Miele Medical Equipment, producing error message Fdo, it means the liquid detergent container is empty. Refill or replace the liquid detergent container.
P
prossSep 4, 2025
Why are there spots on items from my Miele Medical Equipment?
- M
  Michael WebbSep 5, 2025
  If you're noticing spots on items after washing them in your Miele Medical Equipment, it could be because: * The rinse aid setting is too low. Try increasing the rinse aid dosage. * The rinse aid container is empty. Add rinse aid to the container.
J
Jennifer DelgadoSep 6, 2025
What to do when the neutralizer light flashes and the program stops on my Miele Medical Equipment?
- M
  michael74Sep 6, 2025
  If, a few minutes after the start of a program, the "Neutralizer" indicator light flashes and the program stops on your Miele Medical Equipment, producing error message Fdo, it indicates a problem dispensing the neutralizer. Refill or replace the neutralizer container and prime the dosage system.