Need help?Do you have a question about the Milli-Q ZR0Q00800 and is the answer not in the manual?
General| Model | ZR0Q00800 |
|---|---|
| Resistivity | 18.2 MΩ·cm at 25 °C |
| TOC | < 5 ppb |
| Pyrogens (Endotoxins) | < 0.001 EU/mL |
| RNases | < 1 pg/mL |
| Flow Rate | Up to 2 L/min |
| Feed Water Type | Tap Water |
| Output Water Quality | Ultrapure water |
| Particles > 0.22 μm | < 1 particle/mL |
| Bacteria | < 1 CFU/mL |
| Power Supply | 100-240 V AC, 50-60 Hz |
Details the purpose, terminology, and document identification for the user manual.
Provides contact information and manufacturing site details for Millipore SAS.
Covers notice, product warranty, trademarks, copyright, and recycling guidelines.
Covers general safety statements, symbols, and important operational guidelines.
Introduces topics related to the system, including requirements and components.
Details the main unit of the system and its components.
Describes the recommended reservoirs for the system.
Lists and describes the various consumables used by the system.
Outlines the technical specifications and operational requirements for the system.
Explains the purpose of the chapter and lists installation topics with page numbers.
Provides a step-by-step summary of the system installation process.
Explains common alarm messages generated during system installation.
Instructions for separating and placing the POD Arm onto the POD Mast.
Lists and describes the system's tubing, cables, and power cord connections.
Step-by-step instructions for installing a new Progard® Cartridge.
Step-by-step instructions for installing a new Q-Pak® Pack.
Explains the importance and procedure for flushing and rinsing RO cartridges.
Step-by-step instructions for rinsing the Q-Pak® Pack.
Outlines steps for installing and registering a POD Pak.
Explains the need to reset UV lamp timers and provides the procedure.
Procedure to reset the timer for the PERFORM RO CL2 CLEANING message.
Procedure to reset the timer for the EXAMINE INLET STRAINER message.
Explains that flow rate calibration is needed upon system installation.
Explains how to perform a TOC Curve Check to ensure valid TOC values.
Introduces the chapter explaining the various software used in the system.
Visual representation of the system's software structure and navigation.
Explains the primary uses of the STANDBY mode and its interface.
Introduces the Manager Menu, how to enter it, and its functions.
Explains water dispensing and viewing parameters in READY mode.
Introduces the chapter on dispensing water and viewing system information.
Provides instructions on dispensing water using the POD Unit plunger.
Step-by-step instructions for viewing the water quality parameters.
Explains how to view system operation, alerts, alarms, and measures.
Details how to view information related to the status of consumables.
Explains how to access contact information for Millipore SAS representatives.
Explains how to view flow schematic, version, and system information.
Introduces the chapter on common maintenance procedures for the system.
Details maintenance needed for consumables, UV lamps, cleaning, and calibration.
Specifies when to replace the Progard® Cartridge and Vent Filter.
Specifies when to replace the Q-Pak® Pack and provides removal/installation steps.
Discusses POD Pak replacement based on flow rate, messages, and provides registration steps.
Specifies when a TOC Curve Check should be performed and provides the procedure.
Specifies when RO cartridge sanitisation is required and provides the procedure.
Specifies when cleaning the RO cartridge may be required and provides the procedure.
Explains the purpose and procedure for cleaning the inlet strainer.
Specifies when the flow rate should be calibrated.
Introduces the chapter on alarm messages and how to manage them.
Defines alarms, explains display, types, and how to cancel them.
Lists alarm messages that stop the system and explains their meanings.
Introduces the chapter on alert messages and how to manage them.
Explains alerts, their types, examples, and how they appear on the display.
Lists various alert messages and their corresponding meanings and actions.
Lists catalogue numbers for Milli-Q Direct systems, consumables, and accessories.
To Next Page
