Milnor Phase 7.2.2 - Page 33

92 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

31

From

Previous

GAS REVERSING

Press the up or down arrow

key to select a different model.

GAS REVERSING, ELECTRIC

REVERSING, STEAM

REVERSING, GAS NON-

REVERSING, ELECTRIC

NON-REVERSING and

STEAM NON-REVERSING

are the selections.

ELECTRIC

REVERSING

1: SYSTEM TEMP

Press ENTER to access

Press ENTER to store

new changes

Table of Contents

Default Chapter3
- Table of Contents3
Section I5
Introduction5
- Phase 7 Non-Coin Microprocessor Controller (Computer) Drying System5
Section II6
Features6
- Dependable Phase 7 Non-Coin Microprocessor Controller (Computer) Solid State Integrated Circuitry6
- Fire Suppression System (F.S.S.)6
- Program Changes Are Easily Made at the Keyboard (Touch Pad)6
- Automatic Drying Cycle (Patent No. 4,827,627)6
- Timed (Manual) Drying Cycle6
- Preprogrammed Cycles6
- Manually Loaded Cycles6
- Variable (Programmable) Fabric/Temperature Selections6
- Cool Down/Controlled Cool down Program6
- Temperature Conversion Status7
- High Temperature Protection7
- Cycle Preview7
- Reversing Option7
- Rotation Sensor7
- Clean Lint7
- Language Selection7
- Model Selection7
- Default Factory Settings7
- Keyboard (Touch Pad) Symbols7
Section III8
Program Selections8
- Preprogrammed Cycles8
- Manually Loaded Cycles10
- Automatic Drying Cycle (Patent No. 4,827,627) Operations10
- Timed (Manual) Drying Cycle Operation10
- Light Emitting Diode (L.E.D.) Dot Matrix Display11
- Cycle in Progress Temperature Display11
- Temperature Conversion Status11
- Wrinkle Guard Program12
- Audio Alert on Times 0 to 1012
- Preprogrammed Cycle Preview12
- Diagnostics13
- Program Locations13
- Reversing Option13
Section IV16
Operating Instructions16
- Operating Sequence16
- Operating Notes20
- Fire Suppression System (F.s.s.) Theory of Operation21
Section V24
- L.e.D. Display Messages24
- L.e.D. Display Operating Status24
- Cycles in Progress24
- Cycle Status24
Section VI25
Programming Instructions25
- Introduction to Programming25
  - Entering the Programming Mode25
  - Exiting the Programming Mode25
- Programming Flowcharts27
Section VII77
Factory Preset Parameters (Programs)77
- Cycle "A-F" Parameters (Programs) Preset by the Factory77
- Cycle "0-40" Parameters (Programs) Preset by the Factory77
Section VIII78
Programming Limits78
- Phase 7 Non-Coin Microprocessor Controller (Computer Programming Limits78
- Preprogrammed Cycles78
- Fixed Parameters79
- System Parameters (Program Locations)79
Section IX80
Phase 7 Non-Coin Auto Cycle (Patent No. 4,827,627) Cycle Adjustment Values80
Section X81
- Diagnostic (L.e.D. Display) Fault Messages81
  - Burner Control Fault81
  - Ignition Fault81
Phase 7 Non-Coin Microprocessor Controller (Computer) System Diagnostics81
- Burner High-Limit Fault82
- Burner Purge Fault82
- Check Control Board Fuse82
- Flame Fault82
- Exhaust High Temp Fault83
- Exhaust High-Limit Fault83
- Exhaust Probe Fault/Axial Probe Fault83
- Model Error, Enter Correct Model83
- F.s.s. Activated84
- Rotation Sensor Fault84
- Sail Switch Closed Fault84
- Sail Switch Open Fault84
- B. F.s.s. Diagnostic Conditions85
- Disconnected Water Valve85
- Input/Output (I/O) Board L.e.D. Indicators86
- Keyboard (Touch Pad) Layout87
Section XI88
Customer Custom Parameter Settings88

Related product manuals

Preview: Milnor E-P Plus

Milnor E-P Plus

Milnor 30010CGE

Preview: Milnor MilTouch

Milnor MilTouch

Preview: Milnor MWF27Z8 Series

Milnor MWF27Z8 Series