For safe operation
6
Never do the following
WARNING
Do not disassemble or remodel the machine
• Never disassemble or remodel this machine and the
ink bottle.
Disassembling or remodeling any of them will result in
electric shocks or breakdown of this machine.
Power supply and voltage
• Use this machine with indicated power specifications.
Be sure to connect the power cable plug to the
grounded outlet, or it may cause fire or electric shock.
• Never look at the LED UV being lit with your naked
eyes, or it may cause pain in your eyes or visual
impairment. Be sure to wear safety glasses.
• Do not apply ultraviolet (UV) light directly to your skin,
or it may cause irritation on your skin.
• To prevent electrical shock, be sure to set OFF the
main power circuit breaker and disconnect the power
plug before carrying out maintenance. For some units,
capacitors may take one minute for discharging;
therefore, start maintenance work three minutes after
setting OFF the main power circuit breaker and
disconnecting the power plug.
• If LED UV has been damaged, you should replace the
LED UV that has reached or has past its rating life.
• The main power circuit breaker should be set ON only
by personnel with sufficient knowledge about
operations of this machine.
• Do not touch the lamp with bare hands while lighting or
right after the lamp off to avoid from burn injury.
• Although this device is a Class 1 laser device, its laser
sensors are equipped with Class 2 lasers. Never look
directly at the laser light, as it can make your eyes hurt
or damage your eyesight.
Do not use this machine in damp places
• Avoid damp environment to use this machine. Do not
splash water onto this machine. High humidity or water
will give rise to fire, electric shocks or breakdown of
this machine.
Abnormal event occurs
• If the machine is used under an abnormal condition
where the machine produces smoke or unpleasant
smell, fire or electric shocks can result. Be sure to turn
off the power switch immediately and detach the plug
from the receptacle. Check first to be sure that the
machine no longer produces smoke, and contact a
distributor in your district for repair.
• Never repair your machine by yourself since it is very
dangerous for you to do so.
Handling of ink bottles
• Some of the ingredients (UV Curing initiator) have
toxic consequences to aquatic life. Avoid leak into
water system or sewage containing water.
• Store ink bottles and waste ink tank in a place that is
out of the reach of children.
• If ink settles on the skin or clothes, immediately wash it
off with detergent or water. If you get ink in your eyes,
immediately wash your eyes with a lot of clean water,
and then consult a doctor as soon as possible.
Handling of the power cable
• Use a power cable attached to this machine.
• Take care not to damage, break or work on the power
cable. If a heavy things are put on the power cable,
heated or drawn, the power cable can break to cause
fire or electric shocks.
Handling of LED UV
• Do not use the LED UV in an ambience with a
possibility of catching fire (gasoline, combustible gas
spray, thinner, lacquer, powder dust, etc.). In addition,
do not put paper or cloth near or on the LED UV, or it
may cause fire, or it may cause electrical shock.
Handling of the antifreeze liquid
• Use the exclusive antifreeze liquid, or the cooling
device may be damaged.
• If the antifreeze liquid or mixed soft water with
antifreeze liquid gets on the skin or clothes,
immediately wash it off with soap.
If you get the antifreeze liquid in your eyes,
immediately wash your eyes with a lot of clean water.
Then, consult a doctor as soon as possible.
• Before using the antifreeze liquid, be sure to read the
Material Safety Data Sheet (SDS).
• If you swallowed the antifreeze liquid accidentally, try
to get to vomit, and then consult a doctor as soon as
possible.
• Discard the waste antifreeze liquid or used mixed soft
water with antifreeze liquid as follows;
Absorb in a sawdust or waste cloth, then incinerate it.
• Entrust to an industrial waste disposal contractor,
clarifying their contents.
• Avoid causing ignition with static electricity, impact
spark and so on.
• Be sure to wear goggles and gloves for handling the
antifreeze liquid.
Circulating water
• If you find any water leaks on the maintenance
parts, turn the power switch off immediately,
and remove the power plug from the power
socket.
Note on maintenance
• When cleaning the ink-station or the heads, make sure
to wear the attached goggles and gloves.
• The gloves supplied with the machine are disposable.
When all the gloves are expended, purchase an
equivalent product on the market.
WARNING
To Next Page
Loading...
Need help?
General