DETECTOR SET UP SKIN APPLICATION
North & South America
Minelab Americas Inc
+1 630 401 8150
info@minelabamericas.com
Asia Pacic
Minelab Electronics Pty Ltd
+61 8 8238 0888
minelab@minelab.com.au
Europe
Minelab International Ltd
+353 21 423 2352
minelab@minelab.ie
Middle East & Africa
Minelab MEA General Trading LLC
T: +971 4 254 9995
minelab@minelab.ae
WARRANTY TERMS
This product has a 2 year limited warranty from the
time of purchase. Please refer to www.minelab.com
for further warranty information.
COMPLIANCE
Information to the User (FCC Part 15.105)
NOTE: Class B Devices
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment
and receiver
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected
• Consult the dealer or an experienced radio/TV
technician for help
Warning: Any changes or modifications not
expressively approved by Minelab Electronics could
void the user’s authority to operate this equipment.
CODE OF ETHICS
1. Respect the rights and property
of others.
2. Observe all laws, whether
national, state or local.
3. Never destroy historical or
archaeological treasures.
4. Leave the land and vegetation
as it was.
5. Always obtain permission before
searching sites.
6. Always ll in your holes after
digging.
DOWNLOAD APP
www.itunes.com | play.google.com
NOTE:
GO‑FIND App works with
GO‑FIND44/66 only.
Pro App FREE with GO‑FIND66 only.
BLUETOOTH SMART COMPATIBLE
GO-FIND 44/66 are BLUETOOTH SMART
compatible with iOS 8 and Android 4.3 mobile
operating systems, and above.
4901-0230-2
STEP 1. Lift the handle. STEP 2. Insert 4 x 1.5V AA (LR6) batteries
(not included).
STEP 1. There are two skins provided.
To apply, simply peel backing paper
from selected skin.
STEP 2. Then apply selected skin to
body of detector as shown.
STEP 3. Slide out the armrest to desired length
(typically just under your elbow).
STEP 4. Fold out the search coil to detect parallel
with the ground (Refer to ‘Detecting Basics’). Tighten
the nut to x the coil position. Be careful not to
over tighten.
STEP 5. Fully extend the lower shaft until you
you hear it click into place.
STEP 6. Release the camlock lever to adjust the
upper shaft to desired length, for your height
(Refer to ‘Detecting Basics’). Close the camlock lever
to lock into position.
To retract shaft, rmly tap on the base of the coil.
www.minelab.com
4 x AA
GETTING STARTED GUIDE
To release handle, press and hold down both
unlock buttons while folding handle at.
(failure to release handle correctly will result in damage).
Minelab® and GO-FIND® are trademarks of Minelab Electronics Pty. Ltd. Images and graphics are for illustration purposes only;
product conguration and specications may vary from those shown.
To Previous Page
Loading...
Need help?
General
