Mitsubishi Electric DLP FD730U User Manual (English)

Other manuals for Mitsubishi Electric DLP FD730U

Questions and Answers:

J
Joseph McgrathAug 14, 2025
Why does my Mitsubishi Electric Projector show 'No Signal'?
- T
  Tanner RamirezAug 14, 2025
  If your Mitsubishi Electric Projector displays a 'No Signal' message, several factors could be at play. First, ensure the connected device is powered on and functioning correctly, and that it is outputting signals. Check the cable connecting the projector to the external device for any defects. Verify that you're using the correct terminals for the connection. Also, confirm that the connected device is correctly selected as the input source on the projector. If you're using an extension cord, try replacing it with the supplied cable to see if that resolves the issue; if it does, consider using an RGB signal amplifier with the extension cord.
M
Melissa AlexanderAug 17, 2025
How to fix a Mitsubishi Electric Projector when no image appears?
- C
  Christy SullivanAug 17, 2025
  If no image appears on the screen of your Mitsubishi Electric Projector, try the following: * Cancel AV mute by pressing the AV MUTE button. * Ensure the lens cap is removed. * Note that it can take up to 1 minute for the lamp to light up. * If the lamp doesn't light, wait a few minutes and try again. * If the projector was turned off before cooling, the fan may start and the POWER button might not work after plugging in the power cord. * Check the intake vent is clean. * Ensure the lamp cover is closed. * Verify the cables connected to external devices are not broken. * If using an extension cable, replace it with the supplied cable to check; if images display correctly, add an RGB signal amplifier to the extension cable.
M
Melissa HoltAug 21, 2025
What to do if Mitsubishi Electric DLP FD730U images are blurred?
- T
  Thomas KingAug 21, 2025
  If the images projected by your Mitsubishi Electric Projector appear blurred, you can try the following steps: Adjust the focus. Clean the lens. Press the ? or ? button on the remote control to eliminate flicker. You can also adjust TRACKING and FINE SYNC in the SIGNAL menu. Additionally, adjust BRIGHTNESS and CONTRAST in the QUICK MENU or the IMAGE menu. Finally, make sure that the projector and the screen are perpendicular to each other.
T
Trevor PowellAug 25, 2025
Why is my Mitsubishi Electric DLP FD730U remote control not working?
- C
  Cindy SmithAug 25, 2025
  If the remote control for your Mitsubishi Electric Projector isn’t working correctly, make sure the batteries are properly loaded and not weak. Ensure the remote control sensor isn’t exposed to direct sunlight or fluorescent light. Use the remote control within its operational range and keep it at least 10 cm away from the projector.
C
catherine05Aug 27, 2025
What causes shaking or displaced images on a Mitsubishi Electric Projector?
- J
  Jennifer MartinAug 27, 2025
  Shaking or displaced images on your Mitsubishi Electric Projector can be due to a few reasons. First, check that the cable connected to the external device isn’t intermittent and ensure the cable’s plug is firmly connected to the external device’s connector. You can also try pressing the AUTO POSITION button. If the issue persists, some computers may output out-of-spec signals; in this case, adjust the SIGNAL menu.
A
Audrey HarrisonAug 31, 2025
Why are my Mitsubishi Electric DLP FD730U images dark?
- B
  bryan36Aug 31, 2025
  If the images from your Mitsubishi Electric Projector appear dark, try adjusting the BRIGHTNESS and CONTRAST in the QUICK MENU or the IMAGE menu. If adjusting these settings doesn't resolve the issue, you may need to replace the lamp.
D
Dana WrightSep 3, 2025
What causes flickering images on a Mitsubishi Electric DLP FD730U Projector?
- M
  Michael ColemanSep 3, 2025
  Flickering images on your Mitsubishi Electric Projector may occur after pressing the POWER or ON button on the remote, or when the LAMP MODE setting has changed; this should stabilize once the lamp lights fully. Also, flickering may temporarily occur when selecting the input signal, Auto Position, and Color Enhancer.
K
Kimberly EvansSep 6, 2025
Why are images distorted on my Mitsubishi Electric DLP FD730U Projector?
- J
  John GordonSep 6, 2025
  To correct distorted images on your Mitsubishi Electric Projector, adjust the position of the projector and the screen to ensure they are perpendicular to each other.
M
Micheal NguyenSep 10, 2025
How to resolve afterimages on Mitsubishi Electric Projector screen?
- J
  Joshua MossSep 10, 2025
  To improve afterimages persisting on the screen of your Mitsubishi Electric Projector, keep projecting an evenly bright image.