Mitsubishi Electric DLP XD700U User Manual (English)

Questions and Answers:

T
Teresa AlexanderAug 18, 2025
Why no image appears on Mitsubishi Electric DLP XD700U Projector?
- A
  Andrea Jones DVMAug 18, 2025
  If no image appears on the screen of your Mitsubishi Electric Projector, consider the following: * Ensure that AV mute is canceled by pressing the AV MUTE button. * Verify that the lens cap is removed. * Allow approximately 1 minute for the lamp to light up. * If the lamp doesn't light, wait a few minutes and try again. * If the projector was turned off before the lamp cooled, press the POWER button to turn the power indicator back on. * Confirm the intake vent is clean and the lamp cover is closed. * Check for broken cables connected to external devices; replace extension cables with supplied cables for testing. If images then display correctly, add an RGB signal amplifier to the extension cable.
J
Joan MartinezAug 21, 2025
What to do if Mitsubishi Electric DLP XD700U power can not be turned on?
- K
  Kevin WallaceAug 21, 2025
  If your Mitsubishi Electric Projector power won't turn on, check these items: * Ensure the power cord is correctly connected to both the projector and a functioning wall outlet. * Remove any obstructions blocking the intake or exhaust vents. If vents were blocked: 1. Unplug the power cord. 2. Let the projector cool down. 3. Plug the cord back in. 4. Press the POWER button. * Make sure the exhaust vents aren't exposed to hot air from heating appliances. * If the STATUS indicator is steady red, replace the lamp, as it may be at the end of its life. * Ensure the lamp cover is attached securely. If the issue persists, unplug the projector and contact your dealer.
A
Ashley JordanAug 23, 2025
Why does Mitsubishi Electric DLP XD700U power turns off?
- J
  Jason FigueroaAug 23, 2025
  If your Mitsubishi Electric Projector turns off unexpectedly, here’s what to check: * Ensure that the intake and exhaust vents are not blocked. If they are, remove any obstructions, then: 1. Wait for the fans to stop and the STATUS indicator to go out. 2. Unplug the power cord. 3. Wait 10 minutes. 4. Plug the cord back in. 5. Press the POWER button. * If the STATUS indicator is steady red, replace the lamp. * Verify that the Auto Power Off setting is disabled. * Note that a deteriorated lamp may turn off shortly after illuminating.
R
Ronald BennettAug 25, 2025
What to do if Mitsubishi Electric DLP XD700U displays “No signal”?
- S
  srichardsonAug 26, 2025
  If your Mitsubishi Electric Projector displays a “No signal” message, try the following steps: * Ensure the connected device is powered on and functioning correctly. * Verify the external device is outputting signals. * Check the cable connecting the projector to the external device for any defects. * Confirm the projector is connected to the external device using the correct terminals. * Make sure the connected device is correctly selected as the input source. * If using an extension cord, replace it with the supplied cable to see if images project correctly. If they do, use an RGB signal amplifier with the extension cord.
M
Matthew FullerAug 27, 2025
How to fix shaking images on Mitsubishi Electric DLP XD700U Projector?
- J
  johnstonjacquelineAug 27, 2025
  If the projected images from your Mitsubishi Electric Projector are shaking or displaced: * Check the cable connected to the external device to ensure it isn't intermittent. * Securely connect the cable's plug to the external device's connector. * Press the AUTO POSITION button. * If using a computer, adjust the Signal menu as some computers may output out-of-spec signals. * For WXGA video signals, confirm the correct setting is selected in the WXGA option menu. For other signals, ensure WXGA is set to Off.
S
samantha84Aug 30, 2025
How to fix blurry images on Mitsubishi Electric DLP XD700U Projector?
- C
  Carrie CarrilloAug 30, 2025
  To resolve blurry projected images on your Mitsubishi Electric Projector: * Adjust the focus. * Clean the lens. * Press the ? or ? button on the remote control to eliminate flicker. * Adjust Tracking and Fine sync in the Signal menu. * Adjust Brightness and Contrast in the Picture menu. * Ensure the projector and screen are perpendicular to each other.
V
vandradeSep 1, 2025
How to fix dark images on Mitsubishi Electric Projector?
- G
  Gina HaleSep 1, 2025
  If the projected images from your Mitsubishi Electric Projector are too dark, try adjusting the Brightness and Contrast settings in the Picture menu. If the issue persists, consider replacing the lamp.
E
eduardo30Sep 3, 2025
How to fix distorted images on Mitsubishi Electric DLP XD700U Projector?
- J
  jasmine83Sep 3, 2025
  To correct distorted projected images on your Mitsubishi Electric Projector, adjust the projector and the screen so that they are perpendicular to each other.
D
David FletcherSep 6, 2025
How to fix wavy images on Mitsubishi Electric Projector?
- A
  Anne TorresSep 6, 2025
  If the projected images from your Mitsubishi Electric Projector appear wavy: * Ensure the plugs of the cables are securely connected to external devices. * Keep the projector away from equipment that generates interfering radio waves. * If the issue occurs after keystone adjustment, readjust the keystone to minimize the amount of correction applied.
B
Brian CowanSep 8, 2025
Why does Mitsubishi Electric Projector ask for password?
- S
  Shelia SmithSep 8, 2025
  The password screen appears on your Mitsubishi Electric Projector because the Password feature in the Password menu has been enabled. To proceed, enter the password or contact the person managing the projector.

Mitsubishi Electric DLP XD700U Specifications

General

Display Technology	DLP
Native Resolution	XGA (1024x768)
Contrast Ratio	2000:1
Lamp Life (Normal)	2000 hours
Lamp Life (Eco)	3000 hours
Zoom Ratio	1.2x
Input Ports	S-Video
Projection Size	40 - 300 inches