How to unlock password on Mitsubishi Electric Inverter?
If the Mitsubishi Electric Inverter is password locked, enter the password in Pr. 297 Password lock/unlock to unlock the password function before operating.
How to resolve overcurrent trip during deceleration or stop on Mitsubishi Electric FR-E740-5.5K Inverter?
If the Mitsubishi Electric Inverter experiences an overcurrent trip during deceleration or stop, it signifies that an overcurrent has occurred during these phases. Here’s what you can do: * Increase the deceleration time. * Check the wiring for output short circuits or ground faults. * Verify that the mechanical brake isn't activating too early. * Lower the stall prevention operation level. * Activate the stall prevention operation and the fast-response current limit operation (Pr.156). * If the motor is coasting, stop it before issuing a start command. Alternatively, use the automatic restart after instantaneous power failure/flying start function.
How to fix regenerative overvoltage trip during deceleration or stop on Mitsubishi Electric FR-E740-5.5K Inverter?
If your Mitsubishi Electric Inverter is tripping due to regenerative overvoltage during deceleration or stop, it means overvoltage has occurred. Try these solutions: * Increase the deceleration time to match the load's moment of inertia. * Make the brake cycle longer. * Use the regeneration avoidance function (Pr. 882, Pr. 883, Pr.885, Pr.886). * Consider using a brake resistor, brake unit, or power regeneration common converter (FR-CV) as needed.
How to resolve regenerative overvoltage trip during acceleration on Mitsubishi Electric FR-E740-5.5K?
If your Mitsubishi Electric Inverter is tripping due to regenerative overvoltage during acceleration, it means overvoltage has occurred during acceleration. Here are some steps to take: * Decrease the acceleration time. * Implement the regeneration avoidance function using parameters Pr. 882, Pr. 883, Pr.885, and Pr. 886. * Ensure that the stall prevention operation level (Pr. 22) is set correctly.
What to do if Mitsubishi Electric FR-E740-5.5K Inverter shows inverter overload trip?
If the Mitsubishi Electric Inverter experiences an overload trip (electronic thermal O/L relay function), it signifies that the electronic thermal relay function for inverter element protection has been activated. To address this: * Increase the acceleration time. * Adjust the torque boost setting (Pr. 0). * Configure the load pattern selection setting (Pr. 14) according to the machine's load pattern. * Reduce the load. * Ensure the surrounding air temperature is within specified limits.
How to fix overcurrent trip during acceleration on Mitsubishi Electric FR-E740-5.5K Inverter?
If the Mitsubishi Electric Inverter experiences an overcurrent trip during acceleration, it means that an overcurrent has occurred. To resolve this, try the following: * Increase the acceleration time. * Check for output short circuits or ground faults in the wiring. * If 'E.OC1' appears consistently at start, disconnect and restart the inverter. If the problem persists, the inverter may be faulty and you should contact your sales representative. * Ensure the base frequency is correctly set (Pr. 3) for your motor (50Hz). * Reduce the stall prevention operation level and activate both stall prevention and fast-response current limit operations (Pr.156). * For regenerative driving, adjust the base voltage in Pr. 19. * If the motor is coasting, stop it before issuing a start co...
What does fan alarm mean on Mitsubishi Electric FR-E740-5.5K?
If the Mitsubishi Electric Inverter triggers a fan alarm, it indicates that the cooling fan is at a standstill or has decelerated. Check for fan failure and contact your sales representative.
What to do if Mitsubishi Electric FR-E740-5.5K Inverter shows brake transistor alarm detection?
If the Mitsubishi Electric Inverter detects a fault in the brake circuit, such as a brake transistor breakage, replace the inverter.
What causes output phase loss in Mitsubishi Electric FR-E740-5.5K?
If the Mitsubishi Electric Inverter detects a loss in one of the three output phases (U, V, W) during operation, ensure the cables are properly wired. If the motor capacity is smaller than the inverter capacity, choose matching inverter and motor capacities.
What to do if Mitsubishi Electric FR-E740-5.5K Inverter shows regenerative brake pre-alarm?
If the Mitsubishi Electric Inverter's regenerative brake duty reaches 85% of the Pr. 70 Special regenerative brake duty setting or higher, set a longer deceleration time and check the settings of Pr.30 Regenerative function selection and Pr. 70 Special regenerative brake duty.
Basic wiring instructions for connecting the inverter, power supply, motor, and peripheral devices.
Measures to suppress electromagnetic interference and manage leakage currents for compliance and system stability.
General safety and handling precautions to prevent product damage, shorten lifespan, or ensure correct operation.
Methods for implementing system failsafe using inverter status output signals and external backup systems.
Comprehensive list of all inverter parameters, their settings, and related pages for detailed information.
Procedures for adjusting motor torque, including manual torque boost, automatic control, and stall prevention.
Guidance on selecting motors, motor overheat protection, and using auto-tuning for optimal performance.
Settings for automatic restart and power failure deceleration stop functions to ensure system continuity.
Configuration for retry operation, phase loss protection, and earth fault detection to manage faults.
Procedures for resetting inverter protective functions after a fault or warning occurs.
Reference for understanding and interpreting various fault and alarm codes displayed by the inverter.
Detailed explanations of common causes for errors and warnings, with corresponding corrective actions.
Initial troubleshooting steps and checks to perform when encountering operational issues with the inverter.
General| Brand | Mitsubishi Electric |
|---|---|
| Model | FR-E740-5.5K |
| Category | Inverter |
| Language | English |
To Next Page