Mitsubishi Electric HC4900 User Manual (English)

Other manuals for Mitsubishi Electric HC4900

Questions and Answers:

T
tannersandraAug 22, 2025
How to fix a Mitsubishi Electric HC4900 Projector when no image appears on the screen?
- R
  robertdavidsonAug 22, 2025
  If no image appears on the screen of your Mitsubishi Electric Projector, try the following solutions: Ensure the lens cap is removed. Note that it can take about one minute for the lamp to light up. If the lamp doesn't light up, wait a few minutes and try again. If the projector was turned off before the lamp cooled down, wait for the fan to stop, then press the POWER button. Make sure the intake vent is clean and the lamp cover is closed. Set SCART INPUT in the FEATURE menu to OFF. Check the cables connected to external devices for damage. If using an extension cable, replace it with the supplied cable or add an RGB signal amplifier. Consult the video device's manual for connection instructions.
C
Craig WilliamsSep 1, 2025
What does 'TEMPERATURE!!' mean on my Mitsubishi Electric Projector?
- K
  Kathleen MathewsSep 1, 2025
  The “TEMPERATURE!!” message on your Mitsubishi Electric Projector indicates that the ambient temperature is too high or that the air inlet or outlet grille is blocked. Try to eliminate any causes of the rise in ambient temperature. Also, remove any obstructions from the air inlet or outlet grille and clean the filter if it's clogged.
P
Paul HoodAug 31, 2025
What to do if the menu on my Mitsubishi Electric HC4900 can't be used?
- A
  Andrea BeckAug 31, 2025
  If you can't use the menu on your Mitsubishi Electric Projector, it might be due to the microcomputers inside the projector operating incorrectly because of noise. Try turning off the lamp by pressing the POWER button and wait about 2 minutes. Then, unplug the power cord from the outlet, wait at least 10 minutes, and plug it back in. If the POWER button doesn't function, unplug the power cord from the outlet, wait at least 10 minutes, and then plug it back into the outlet.
J
jpowellAug 30, 2025
Why are the projected images from my Mitsubishi Electric Projector dark?
- A
  aleblancAug 30, 2025
  If the projected images from your Mitsubishi Electric Projector are too dark, try adjusting the BRIGHTNESS and CONTRAST in the IMAGE menu. If that doesn't help, you may need to replace the lamp.
L
Laura MartinAug 28, 2025
Why are the projected images from my Mitsubishi Electric Projector shaking?
- E
  eduardomasonAug 29, 2025
  If the projected images from your Mitsubishi Electric Projector are shaking, check the following: Ensure the cable connected to the external device isn’t intermittent and that the cable’s plug is firmly connected to the external device’s connector. Try pressing the AUTO POSITION button. If the issue persists, some computers may output out-of-spec signals; in this case, adjust the SIGNAL menu.
J
Jacqueline SalinasAug 27, 2025
Why is my Mitsubishi Electric Projector remote control not working?
- K
  kgallegosAug 27, 2025
  If your Mitsubishi Electric Projector remote control isn’t working well or at all, check these things: Make sure the batteries are correctly loaded and not weak. Ensure the remote control sensor isn’t exposed to direct sunlight or fluorescent light. Use the remote control within its operational range and keep it at least 10 cm away from the projector.
D
Douglas MooreAug 27, 2025
How to resolve blurred projected images on Mitsubishi Electric HC4900 Projector?
- C
  chloeturnerAug 27, 2025
  To fix blurred projected images on your Mitsubishi Electric Projector, try these steps: Adjust the focus. Clean the lens. Press the W or X button on the remote control to eliminate flicker. Adjust TRACKING and FINE SYNC in the SIGNAL menu. Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. Ensure the projector and screen are perpendicular to each other.
C
churchkristinaAug 25, 2025
Why does my Mitsubishi Electric Projector power turn off?
- N
  Nancy FrenchAug 26, 2025
  Your Mitsubishi Electric Projector might be turning off due to a few reasons. It could be that the intake and/or exhaust vents are blocked; if so, remove any obstructions, wait for the fans to stop (until the STATUS indicator goes out), unplug the power cord, wait 10 minutes, plug it back in, and press the POWER button. If the STATUS indicator is steady red, the lamp needs replacing. Also, ensure that AUTO POWER OFF is set to OFF. Finally, if the lamp is old, it may be failing after a short time of use.
E
Eric TaylorAug 23, 2025
What to do if my Mitsubishi Electric HC4900 Projector says 'No Signal'?
- M
  Melanie HernandezAug 25, 2025
  If your Mitsubishi Electric Projector displays 'NO SIGNAL', try these steps: First, ensure that the connected device is powered on and functioning correctly. Check that the external device is outputting signals, especially if it's a notebook computer. Verify that the cable connecting the projector to the external device isn't defective and is connected to the correct terminals. Also, confirm that the connected device is correctly selected as the input source. If you're using an extension cord, replace it with the supplied cable to see if that resolves the issue; if it does, use an RGB signal amplifier with the extension cord.

Mitsubishi Electric HC4900 Specifications

General

Resolution	1920 x 1080
Zoom Ratio	1.6x
Display Technology	LCD
Projection Size	40 - 300 in
Inputs	HDMI, Component, VGA
Lens Shift	Vertical: ±60%, Horizontal: ±23%