Appendix 3. Compliance with European EC Directives
Appendix 3-1 Compliance to EC Directives............................................................................................... A3-2
Appendix 3-1-1 European EC Directives ..........................................................................................A3-2
Appendix 3-1-2 Cautions for EC Directive compliance.....................................................................A3-2
Appendix 4. EMC Installation Guidelines
Appendix 4-1 Introduction........................................................................................................................... A4-2
Appendix 4-2 EMC instructions .................................................................................................................. A4-2
Appendix 4-3 EMC measures..................................................................................................................... A4-3
Appendix 4-4 Measures for panel structure............................................................................................... A4-3
Appendix 4-4-1 Measures for control panel unit ...............................................................................A4-3
Appendix 4-4-2 Measures for door....................................................................................................A4-4
Appendix 4-4-3 Measures for operation board panel........................................................................A4-4
Appendix 4-4-4 Shielding of the power supply input section ............................................................A4-4
Appendix 4-5 Measures for various cables................................................................................................ A4-5
Appendix 4-5-1 Measures for wiring in panel....................................................................................A4-5
Appendix 4-5-2 Measures for shield treatment .................................................................................A4-5
Appendix 4-5-3 Servo/spindle motor power cable ............................................................................A4-6
Appendix 4-5-4 Servo/spindle motor feedback cable .......................................................................A4-7
Appendix 4-6 EMC countermeasure parts................................................................................................. A4-8
Appendix 4-6-1 Shield clamp fitting...................................................................................................A4-8
Appendix 4-6-2 Ferrite core...............................................................................................................A4-9
Appendix 4-6-3 Power line filter ......................................................................................................A4-10
Appendix 4-6-4 Surge protector ......................................................................................................A4-15
Appendix 5. Instruction Manual for Compliance with UL/c-UL Standard
Appendix 5-1 Operation surrounding air ambient temperature................................................................. A5-2
Appendix 5-2 Notes for AC servo system.................................................................................................. A5-2
Appendix 5-2-1 General Precaution..................................................................................................A5-2
Appendix 5-2-2 Installation................................................................................................................A5-2
Appendix 5-2-3 Short-circuit ratings..................................................................................................A5-2
Appendix 5-2-4 Peripheral devices ...................................................................................................A5-2
Appendix 5-2-5 Field Wiring Reference Table for Input and Output.................................................A5-2
Appendix 5-2-6 Motor Over Load Protection.....................................................................................A5-2
Appendix 5-2-7 Flange of servo motor..............................................................................................A5-2
Appendix5-3 AC Servo/Spindle System Connection................................................................................. A5-3
Appendix 6. Transportation Restrictions for Lithium Batteries
Appendix 6-1 Restriction for packing.......................................................................................................... A6-2
Appendix 6-1-1 Target products........................................................................................................A6-2
Appendix 6-1-2 Handling by user......................................................................................................A6-3
Appendix 6-1-3 Reference ................................................................................................................A6-4
Appendix 6-2 Issuing domestic law of the United State for primary lithium battery transportation.......... A6-5
Appendix 6-2-1 Outline of regulation.................................................................................................A6-5
Appendix 6-2-2 Target products........................................................................................................A6-5
Appendix 6-2-3 Handling by user......................................................................................................A6-5
Appendix 6-2-4 Reference ................................................................................................................A6-5
Appendix 6-3 Example of hazardous goods declaration list ..................................................................... A6-6
Appendix 7. Compliance with China Compulsory Product Certification (CCC Certification) System
Appendix 7-1 Outline of China Compulsory Product Certification System............................................... A7-2
Appendix 7-2 First Catalogue of Products subject to Compulsory Product Certification ......................... A7-2
Appendix 7-3 Precautions for Shipping Products ...................................................................................... A7-3
Appendix 7-4 Application for Exemption .................................................................................................... A7-4
Appendix 7-5 Mitsubishi NC Product Subject to/Not Subject to CCC Certification .................................. A7-5
To Next Page
Loading...
