Mitsubishi Electric MELSEC-Q Series - Page 27

27/35
BCN-P5999-0176-2a
Type
Device No.
Application
Word
U00-G2434+100n (n = 0 to 15)
1st Data Pointer (Axis 1 to 16)
U00-G2435+100n (n = 0 to 15)
Pos. Data No. (Axis 1 to 16)
U00-G2436+100n (n = 0 to 15)
Block No. (Axis 1 to 16)
U00-G2437+100n (n = 0 to 15)
Previous Position (Axis 1 to 16)
U00-G2438+100n (n = 0 to 15)
Acc. Time, Dec. Time, Operation Pattern, Control System
(Axis 1 to 16)
U00-G2441+100n (n = 0 to 15)
Int. Axis (Axis 1 to 16)
U00-G2448+100n (n = 0 to 15)
OPR Increment (Axis 1 to 16)
U00-G2450+100n (n = 0 to 15)
Actual Present Value (Axis 1 to 16)
U00-G2452+100n (n = 0 to 15)
Error Counter Value (Axis 1 to 16)
U00-G2454+100n (n = 0 to 15)
Number of Motor Rotation (Axis 1 to 16)
U00-G2456+100n (n = 0 to 15)
Motor Current Value (Axis 1 to 16)
U00-G2464+100n (n = 0 to 15)
Servo Amplifier S/W No._1, 2 (Axis 1 to 16)
U00-G2465+100n (n = 0 to 15)
Servo Amplifier S/W No._3, 4 (Axis 1 to 16)
U00-G2466+100n (n = 0 to 15)
Servo Amplifier S/W No._5, 6 (Axis 1 to 16)
U00-G2467+100n (n = 0 to 15)
Servo Amplifier S/W No._7, 8 (Axis 1 to 16)
U00-G2468+100n (n = 0 to 15)
Servo Amplifier S/W No._9, 10 (Axis 1 to 16)
U00-G2469+100n (n = 0 to 15)
Servo Amplifier S/W No._11, 12 (Axis 1 to 16)
U00-G2470+100n (n = 0 to 15)
Parameter Error No. (Axis 1 to 16)
U00-G2476+100n (n = 0 to 15)
Zero Speed, Zero Point Passed (Axis 1 to 16)
U00-G2477+100n (n = 0 to 15)
Ready ON, Servo ON, Servo Alarm, In-Position, Torque Limit,
Abs. Value Cleared, Warning (Axis 1 to 16)
U00-G2478+100n (n = 0 to 15)
Regenerative Load Ratio (Axis 1 to 16)
U00-G2479+100n (n = 0 to 15)
Actual Load Ratio (Axis 1 to 16)
U00-G2480+100n (n = 0 to 15)
Peak Load Ratio (Axis 1 to 16)
U00-G4093+4p ( p = 0 to 15)
Error History_ Axis (No.0 to No.15)
U00-G4094+4p ( p = 0 to 15)
Error History_ Code (No.0 to No.15)
U00-G4095+4p ( p = 0 to 15)
Error History_ Day, Hour (No.0 to No.15)
U00-G4096+4p ( p = 0 to 15)
Error History_ Minute, Second (No.0 to No.15)
U00-G4158+4p ( p = 0 to 15)
Warning History_ Axis (No.0 to No.15)
U00-G4159+4p ( p = 0 to 15)
Warning History_ Code (No.0 to No.15)
U00-G4160+4p ( p = 0 to 15)
Warning History_ Day, Hour (No.0 to No.15)
U00-G4161+4p ( p = 0 to 15)
Warning History_ Minute, Second (No.0 to No.15)
U00-G4231
Emergency Stop Input
U00-G4256+p ( p = 0 to 15)
Error History_ Month (No.0 to No.15)
U00-G4272+p ( p = 0 to 15)
Warning History_ Month (No.0 to No.15)
U00-G28408+100n (n = 0 to 15)
Gain Adjust Mode Selection (Axis 1 to 16)
U00-G28409+100n (n = 0 to 15)
Auto Tuning Response (Axis 1 to 16)
U00-G28424+100n (n = 0 to 15)
Load to Motor Inertia Ratio (Axis 1 to 16)
U00-G28425+100n (n = 0 to 15)
Model Loop Gain (Axis 1 to 16)
U00-G28426+100n (n = 0 to 15)
Position Loop Gain (Axis 1 to 16)
U00-G28427+100n (n = 0 to 15)
Speed Loop Gain (Axis 1 to 16)
U00-G28428+100n (n = 0 to 15)
Speed Integral Compensation (Axis 1 to 16)
U00-G31300+p ( p = 0 to 15)
Error History_ SV (No.0 to No.15)
U00-G31316+p ( p = 0 to 15)
Warning History_ SV (No.0 to No.15)
U00-G53200
Cam Auto-generation Request
U00-G53201
Cam Auto-generation Cam No.
U00-G53202
Cam Auto-generation Type
U00-G53204
Cam Resolution
U00-G53206
Sheet Length
U00-G53208
Sheet Synchronization Width
U00-G53210
Synchronous Axis Length
U00-G53212
Synchronization Starting Point
U00-G53214
Synchronous Section Acceleration Ratio