Why is the L RUN LED not turning on for my Mitsubishi Electric Control Unit?
If the L RUN LED does not turn on for your Mitsubishi Electric Control Unit, and data link is established, it may be because the transmission speed setting of the master station was changed. Power off and on the system. Also, check that the communication cable is correctly wired.
Why is the Module READY (X0) not turning on, or taking a long time to turn on, on my Mitsubishi Electric MELSEC-Q Controller?
The Module READY (X0) on your Mitsubishi Electric Controller might not turn on promptly due to the module not being ready. Depending on the set number in the access target CPU setting, it may take several minutes until X0 turns on. Another reason could be that many files are stored on the CompactFlash card, which lengthens the time required for X0 to turn on. Delete unnecessary files from the CompactFlash card to resolve this issue.
What to do if CompactFlash card setting status (X1) does not turn on, or it takes a long time to turn on, on Mitsubishi Electric MELSEC-Q?
If the CompactFlash card setting status (X1) on your Mitsubishi Electric Controller doesn't turn on or takes a long time, it may be because the file access stop status is active (X2 is on). Cancel the file access stop status to resolve this. Another potential cause is having many files stored on the CompactFlash card, which lengthens the time required for X1 to turn on. In this case, deleting unnecessary files in the CompactFlash card may help.
What to do if the ERR. LED is on for Mitsubishi Electric Control Unit?
If the ERR. LED is on for your Mitsubishi Electric Control Unit, the transmission speed setting switch or the point mode setting switch may be incorrectly set. Correct the setting, then power off and on the system or reset the CPU module.
Why values of buffer memories cannot be restored to default settings in Mitsubishi Electric I/O Systems?
The values of buffer memories cannot be restored because the Conversion enable/disable setting (Un\G0) has a channel of conversion enable. Set Conversion enable/disable setting (Un\G0) to Disable (1) for all channels, then execute the default setting registration function.
What to do if I can't check the I/O data and parameter data of the slave module on my Mitsubishi Electric Controller?
If you cannot check the I/O data and parameter data of the slave module on your Mitsubishi Electric Controller, verify the following: Ensure that the information regarding the slave module has been properly assigned and that the commands written in the program are correct. Check that the address of the slave module is within the number of transmission points of the master module. Examine the I/O LED status of the slave module and check for any disconnections, short circuits, or poor contact in the wiring on the load side. Ensure that only one master module is connected within one AnyWireASLINK line.
Why is the ALM LED on the Mitsubishi Electric MELSEC-Q Controller master module flashing rapidly (0.2-second intervals)?
If the ALM LED on the master module of your Mitsubishi Electric Controller is flashing at 0.2-second intervals, consider these checks: Adjust the power supply voltage of the 24VDC external power supply to be within the rated value (21.6VDC to 27.6VDC). Make sure the power cables (24V, 0V) are neither disconnected nor short-circuited. Confirm that the 24VDC external power supply is correctly connected to the terminal blocks of both the master and slave modules.
How to resolve CH? Rate alarm warning detection period error in Mitsubishi Electric I/O Systems?
Set CH? Rate alarm warning detection period (Un\G118 to Un\G125) to within 10 to 5000ms. Also, ensure CH? Rate alarm warning detection period (Un\G118 to Un\G125) is equal to or a multiple of the conversion cycle of CH? digital output value (ms).
What to do if Mitsubishi Electric MELSEC-Q shows error code 4?
If the Mitsubishi Electric Controller displays error code 4, it means data outside the allowed setting range was entered. To fix this, ensure that you set the data within the specified range.
Why does my Mitsubishi Electric MELSEC-Q display error code 5?
If the Mitsubishi Electric Controller shows error code 5, this indicates an issue with the upper/lower output limiter or upper/lower setting limiter settings. Ensure that the upper limit value is set to be greater than the lower limit value to resolve this error.
General| Brand | Mitsubishi Electric |
|---|---|
| Model | MELSEC-Q Series |
| Category | Controller |
| Language | English |
To Next Page