Why does my Mitsubishi Electric Air Conditioner smell bad?
If your Mitsubishi Electric Air Conditioner has an unpleasant odor, the indoor unit draws in air that contains gases produced from the walls, carpeting, and furniture as well as odors trapped in clothing, and then blows this air back into the room.
Why does my Mitsubishi Electric Air Conditioner stop before reaching set temperature?
If your Mitsubishi Electric Air Conditioner stops during heating mode before reaching the set temperature, it may be due to frost forming on the outdoor unit when the outdoor temperature is low and the humidity is high. The unit will perform a defrosting operation, and normal operation should resume in about 10 minutes.
What to do if my Mitsubishi Electric Air Conditioner stops when the set temperature is reached?
If your Mitsubishi Electric Air Conditioner stops during cooling mode when the set room temperature is reached, for PLA-EA series, the fan will operate at the lowest speed.
Why doesn't my Mitsubishi Electric Air Conditioner blow warm air immediately?
If your Mitsubishi Electric Air Conditioner doesn't blow warm air from the indoor unit soon after starting heating operation, it is normal. Warm air does not blow until the indoor unit has sufficiently warmed up.
Why won't my Mitsubishi Electric Air Conditioner turn on after turning it off?
If your Mitsubishi Electric Air Conditioner does not operate when restarting it soon after stopping, wait approximately three minutes.
Why does my Mitsubishi Electric Air Conditioner turn off by itself?
If your Mitsubishi Electric Air Conditioner stops without pressing the ON/OFF button, check if the off timer is set and press the ON/OFF button to restart operation. If the air conditioner is connected to a central remote controller or if “ ” appears in the remote controller display, consult the concerned people who control the air conditioner.
Why does my Mitsubishi Electric Air Conditioner turn on by itself?
If your Mitsubishi Electric Air Conditioner operates without pressing the ON/OFF button, check if the on timer is set and press the ON/OFF button to stop operation. If the air conditioner is connected to a central remote controller or if “ ” appears in the remote controller display, consult the concerned people who control the air conditioner. Also, check if the auto recovery feature from power failures has been set and press the ON/OFF button to stop operation.
Why do the vanes move past the set position on my Mitsubishi Electric Air Conditioner?
If your Mitsubishi Electric Air Conditioner vanes always move up and down past the set position before stopping, when the airflow direction is changed, the vanes move to the set position after detecting the base position.
Why does airflow direction change on my Mitsubishi Electric Air Conditioner?
If your Mitsubishi Electric Air Conditioner airflow direction changes during operation or cannot be set, during heating mode, the vanes automatically move to the horizontal airflow direction when the airflow temperature is low or during defrosting mode.
Why is my Mitsubishi Electric Air Conditioner emitting water from the outdoor unit?
If your Mitsubishi Electric Air Conditioner emits water or vapor from the outdoor unit during cooling mode, it may be water forming and dripping from the cool pipes and joints. During heating mode, it may be water forming and dripping from the heat exchanger. During defrosting mode, it may be water on the heat exchanger evaporating.
General| Cooling Capacity | 5.0 kW |
|---|---|
| Heating Capacity | 6.0 kW |
| Power Source | Electric |
| Refrigerant | R32 |
| Coefficient of Performance (Heating) | 4.20 |
| Noise Level (Outdoor Unit) | 50 dB(A) |
| Outdoor Unit Dimensions (HxWxD) | 550 x 800 x 285 mm |
| Indoor Unit Weight | 10 kg |
| Type | Heat Pump |
| Power Supply | 220-240V, 50Hz |
| Series | Mr. Slim |
Important precautions for safe operation and installation to prevent injury or damage.
Identification of key parts of the indoor air conditioning unit.
Overview of the buttons and display on the wired remote controller.
Explanation of various icons displayed on the remote controller screen.
Identification and function of buttons on the wireless remote controller.
Instructions for installing and replacing batteries in the remote controller.
Procedure for starting and stopping the air conditioner operation.
How to choose between Cool, Dry, Fan, Auto, and Heat operation modes.
Guide on adjusting the desired temperature for cooling and heating.
Instructions for selecting the appropriate fan speed for airflow.
How to adjust the vane and louver direction for optimal airflow.
Setting fixed vane angles for specific air outlets.
Configuration of the sensor for detecting occupants and adjusting operation.
Adjusting airflow patterns based on room conditions or occupancy.
Utilizing features like occupancy sensing for energy efficiency.
Adjusting airflow based on season for comfort and efficiency.
How to use the ventilation function with LOSSNAY units.
Programming daily on/off times and temperature settings.
Operating the unit without a functioning remote controller.
Procedures for cleaning air filters and resetting the filter indicator.
Diagnosing and resolving common problems with the air conditioner.
Detailed technical data including power, airflow, and noise levels.
To Next Page
