EasyManua.ls Logo

Mitsubishi Electric VL-50S2-ES2-E - User Manual

Mitsubishi Electric VL-50S2-ES2-E
11 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Eng-1
English
Mitsubishi Lossnay Ventilator
MODELS
VL-50S2-E
(pull cord Type)
VL-50ES2-E
(wall switch Type)
Operating Instructions For Customer
Please read these instructions thoroughly to ensure safe and proper use. After reading, store the manual
in a handy location for easy access.
Before proceeding with operation, please be sure to read “Safety precautions”, as it will tell you how to
operate the Lossnay ventilator properly and safely.
Do not install the unit yourself. (The safety and performance of customer-installed units is not
guaranteed.)
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly
TXDOL¿HGSHUVRQVLQRUGHUWRDYRLGDKD]DUG9/6
2-E only)
- Contact your dealer.
Contents Page
1. Safety precautions ............................... 1
2. When using the unit ............................. 3
3. Features ............................................... 4
4. Names of parts ....................................
%HIRUH\RXVWDUWWKH/RVVQD\ ...............
6. Operation ............................................. 6
7. Maintenance ........................................ 7
8. Troubleshooting ................................... 
6SHFL¿FDWLRQV ....................................... 11
$IWHUVDOHVVHUYLFLQJ ........................... 11
1. Safety precautions
Hazards created by mishandling and their
severity are indicated by the following
markers.
Warning:
This applies to mishandling or misoperation
of the product which could lead to a fatal or
serious injury.
Caution:
This applies to mishandling or misoperation
of the product which will lead to an injury or
damage to your home, household effects, etc.
Warning
- Do not cut, damage or physically
alter the power cord
*1
or subject it
to unreasonable bending, pulling,
twisting or bundling.
- You could damage the cord,
UHVXOWLQJLQ¿UHRUHOHFWULFVKRFN
- Do not turn the Lossnay switch ON
RU2))LIWKHUHLVDÀDPPDEOHJDV
leak.
- 6SDUNVIURPHOHFWULFFRQWDFWVFRXOG
cause explosions. Open a window to
ventilate the room.
Prohibited

Other manuals for Mitsubishi Electric VL-50S2-ES2-E

Questions and Answers

  • E
    Eric RoseSep 15, 2025
    What to do if the shutter is closed on my Mitsubishi Electric Fan?
    • H
      Hector HendersonSep 15, 2025
      Open the shutter.
  • J
    joeforbesAug 25, 2025
    Why is my Mitsubishi Electric Fan so noisy?
    • J
      Justin ArmstrongAug 25, 2025
      If your Mitsubishi Electric Fan is making more noise than usual, ensure that the panel or outside air filter is securely attached. If not, reattach the panel or filter. Also, a clogged outside air filter or exhaust air filter can cause noise. Clean the filter to resolve this.
  • M
    Michelle VasquezAug 25, 2025
    How to troubleshoot a Mitsubishi Electric VL-50S2-ES2-E that does not operate?
    • B
      Brittany VelazquezAug 26, 2025
      If your Mitsubishi Electric Fan unit isn't operating, check the power plug (9/10 62-E only), ensure that a breaker hasn't tripped, and verify that there hasn't been a power failure.
  • A
    Alicia HallAug 26, 2025
    Why is no air coming from my Mitsubishi Electric VL-50S2-ES2-E?
    • T
      Thomas BentleyAug 26, 2025
      If no air or not much air is coming from your Mitsubishi Electric Fan unit, note that the Lossnay is a heat-exchanging ventilator, so the volume of air will be lower than with an ordinary fan. This is normal.
  • A
    Anna WilliamsSep 16, 2025
    Why does my Mitsubishi Electric Fan make noise when operating the shutter knob?
    • R
      rbakerSep 16, 2025
      The sound you hear when operating the shutter knob on your Mitsubishi Electric Fan is the normal operation sound of the shutter inside the product. This is not a malfunction.
  • K
    Kenneth SmithDec 1, 2025
    What to do if my Mitsubishi Electric Air Conditioner Lossnay does not operate?
    • M
      Melissa AveryDec 1, 2025
      If your Mitsubishi Electric Air Conditioner Lossnay is not operating, here are some things to check: * Ensure the power plug is connected to a power source with the correct voltage (220/230/240 VAC). * If there was a power failure, wait for it to recover. * Make sure the circuit breaker is ON. * Check for and securely connect any loose wires on the terminal block or the power supply connector on the main circuit board. * Inspect the fuse on the main circuit board; if it's blown, determine and fix the cause before replacing the main and display circuit boards. * Also, ensure the power cord is properly plugged into the wall outlet and the switch with a pull cord is turned ON. If using a remote controller, make sure you are within the signal range (Front: 4 m, Right: 3 m, Left: 3...
  • M
    Michael WhiteSep 8, 2025
    What to do if cold air enters the room when using Mitsubishi Electric Fan?
    • A
      andrew44Sep 8, 2025
      If cold air may enter inside if inside the room is in negative pressure for a reason such as that the range hood fan is operating, use the Mitsubishi Electric Fan unit in Exhaust only mode.
  • C
    Connor SchmidtSep 9, 2025
    How to stop insects from getting inside my Mitsubishi Electric VL-50S2-ES2-E?
    • J
      Jacob ThompsonSep 9, 2025
      If you notice small insects getting inside your Mitsubishi Electric Fan, it's because small particles and insects may pass through. To enhance trapping efficiency, purchase a high-performance dust filter.
  • B
    Brittany PonceSep 3, 2025
    Why doesn't the operation lamp illuminate on my Mitsubishi Electric Air Conditioner?
    • K
      kimberlyestesSep 3, 2025
      If the operation lamp on your Mitsubishi Electric Air Conditioner isn't lighting up: * Check if the LED on the display circuit board is tilted. If so, attach the LED case cover so that the LED is correctly positioned in the hole of the LED case cover. * Make sure the connector on the display circuit board is securely connected.
  • J
    john55Sep 1, 2025
    How to fix unusual noise coming from the fans of my Mitsubishi Electric Air Conditioner?
    • C
      Christopher HayesSep 1, 2025
      To address unusual noises from the fans of your Mitsubishi Electric Air Conditioner: * First, check for any foreign objects around the fans and remove them. * If you notice any odd sensations when rotating the fan, consider replacing the motor. * Ensure that the Lossnay core and filters are correctly installed.

Mitsubishi Electric VL-50S2-ES2-E Specifications

General IconGeneral
ModelVL-50S2-ES2-E
CategoryFan
Power consumptionLo: 11 W, Hi: 20 W
MountingWall-mounted
Operating voltage220-240 V
Operating frequency50 Hz
Voltage220-240 V
ApplicationResidential
Dimensions168 mm

Related product manuals