APPENDICES
Appendix
1.
WTRUCTIOMS
FOR
COMPLIANCE
WITH THE
EUROPEAN
DIRECTIVES
(LVD
compliant
product
har
CE
marking.)
1.
EMC
DIRECTIVE
Our view
d
inverters
for
the
EMC
Dirsctve
An
inverter
does
not
hndbn
mdently.
lt
b
a compoMnt
designed
for installation
in
a cantrol
box
and tor
use
with
anomer
eguipmenl
to
mtrd
a machin, or
egupment.
Therobre, we
do
not
think that
the
EMC Directive
applies
directly
to
Invecters. Fw
Mls
r-,
we
do
nol
p&w
a CE mark
on the inverter. CE mark placed on
the
inverter shows compliance to
the
Low
Vokage
Diredive. The
European power drive manufacturers’ organization (CEMEP)
also
hob
this
pOml
of
view.
We
do
not
think that
the
inverters themselves are covered directiy
ty
(he
EMC Directive. However,
the EMC Directive
applies
(0
machines and
equipment
into which hv&n
have
teen
incorporated,
and
these
maches
and
Sgupnent
mudt cany
the
CE mark.
Hence,
we
haw
prepared a technical
document ‘EMC
Installation
Guidelines‘ (manual number BCN.A21041-202)
bo
that machines and
equipment
lncorporatlng inverters may conform to
the
EMC Dimcth more
easibj.
Outline
of
installation method
It
is recommended to install an inverter in the following method:
Y
Use
the inverter with an European Standard-compliant noise filter.
#
For wiring between the inverter and motor, use shielded
cables
or run
caMes
in metal conduit
and ground the
caks
or conduit at the inverter and motor ends
Use
the
short&
possble
cable
Y
install the inverter in an grounded metal enclosure. The endosure
should
prevent
died
noise
#
Insart
a
line
noise
finer
and ferrite core into
the
power
and
contrd
li
are required.
Full information including
the
European Standard-compliant nobe filler specificatiw are pubiished
in
the
‘EMC
Installation Guidelines‘ (manual number BCN-A21041-202). Please contact your
sales
representative.
ComplWe
WW
leakage.
2.
Low
Voltage
Directive
Our view of inverters
for
the Low Voltage Directive
Inverter are covered by the Low Voltage Directive.
COmplianCe
We
Mare we meet Low Voltage Directive and place CE
marcOng
on
the mverter.
The European verikation institution has approved that our inverters conform to DIN VDE01W.
Instwions
To conform
to
DIN VDEOl60, the following specifications and instructions
listed
are dinerent from
those of the standard models.
In the 400V class inverters, the rated input voltage range
is
%phase, WV to 415V,
50/60Hz.
Do
not use residual current device as the only protection against indirect contact. Protective
earth connection is essential.
Wire the earth terminal independently.
(Do
not cmnect
two
or more
cables.)
Only use EN or IEC compliant no-fuse breaker and magnetic contractor.
Use
the inverter under condition
of
Over Voltage Category
It
and Pollution Degree
2
or better.
0
Insert an
EN
or IEC Standardcompliant isolation transformer or surge suppresser
to
make
0
Install in a cabinet with IP54 rating or better to have Pollution Degree
2.
For the
input
and output
of
the inverter, only use cables
of
the type and size bet forth
in
EN60204
Appendix C.
The rating of the alarm output relay is 30V DC. 0.3A. There is basic insulation between the a!am
output relay and the inverter control circuit
the Over Voltage Category
II
if power supply over vollage category
is
111
cf
IV.
-
APP
.
1
-
To Next Page
Loading...
