To Next PageTo Next PageWhat does encoder initial communication error 2 mean on Mitsubishi MR-J4-20A?
Encoder initial communication error 2 on your Mitsubishi Amplifier can indicate an encoder malfunction or a load-side encoder malfunction.
What causes encoder initial communication error 1 on Mitsubishi Amplifier?
Encoder initial communication error 1 on your Mitsubishi Amplifier can be caused by: * Encoder initial communication - Receive data error 1. * Encoder initial communication - Receive data error 2. * Encoder initial communication - Receive data error 3. * Encoder initial communication - Transmission data error 1. * Encoder initial communication - Transmission data error 2. * Encoder initial communication - Transmission data error 3. * Encoder initial communication - Process error 1. * Encoder initial communication - Process error 2. * Encoder initial communication - Process error 3. * Encoder initial communication - Process error 4. * Encoder initial communication - Process error 5. * Encoder initial communication - Process error 6.
Why does my Mitsubishi MR-J4-20A Amplifier show an overvoltage error?
An overvoltage error in your Mitsubishi Amplifier is due to a main circuit voltage error.
What does memory error 2 mean on Mitsubishi Amplifier?
Memory error 2 (EEP-ROM) on your Mitsubishi Amplifier can occur due to: * EEP-ROM error at power on. * EEP-ROM error during operation.
What causes encoder normal communication error 1 on Mitsubishi MR-J4-20A Amplifier?
Encoder normal communication error 1 on your Mitsubishi Amplifier can be caused by: * Encoder normal communication - Receive data error 1. * Encoder normal communication - Receive data error 2. * Encoder normal communication - Receive data error 3. * Encoder normal communication - Transmission data error 1. * Encoder normal communication - Transmission data error 2. * Encoder normal communication - Transmission data error 3. * Encoder normal communication - Receive data error 4. * Encoder normal communication - Receive data error 5.
What does encoder normal communication error 2 mean on Mitsubishi MR-J4-20A Amplifier?
Encoder normal communication error 2 on your Mitsubishi Amplifier can be caused by: * Encoder data error 1. * Encoder data update error. * Encoder data waveform error. * Encoder non-signal error. * Encoder hardware error 1. * Encoder hardware error 2. * Encoder data error 2.
What causes a servo control error on my Mitsubishi MR-J4-20A?
A servo control error on your Mitsubishi Amplifier (specifically for linear servo motors and direct drive motors) can be caused by: * Servo control error by position deviation. * Servo control error by speed deviation. * Servo control error by torque/thrust deviation. * Fully closed loop control error by position deviation. * Fully closed loop control error by speed deviation. * Fully closed loop control error by position deviation during command stop.
What does a board error on my Mitsubishi MR-J4-20A mean?
A board error on your Mitsubishi Amplifier indicates: * Board error 1. * Board error 2. * Board error 3.
What causes a regenerative error in my Mitsubishi MR-J4-20A?
A regenerative error in your Mitsubishi Amplifier can stem from: * Regeneration heat error. * Regeneration signal error. * Regeneration feedback signal error.
What does parameter error mean on my Mitsubishi MR-J4-20A?
A parameter error on your Mitsubishi Amplifier indicates either a parameter setting range error or a parameter combination error.
General| Series | MR-J4 |
|---|---|
| Type | AC Servo Amplifier |
| Model | MR-J4-20A |
| Voltage Class | 200 V |
| Control Modes | Position, Speed, Torque |
| Full-closed Control | Yes |
| Advanced One-touch Tuning | Yes |
| Real-time auto-tuning | Yes |
| Vibration Tough Drive | Yes |
| Safety Function | STO (Safe Torque Off) |
| Communication Interface | SSCNET III/H |
| Dynamic Brake | Built-in |
| Rated Output Power | 0.2 kW |
| Output Voltage | 200V |
| Protective Functions | Overcurrent, Overvoltage |
| Ambient Temperature | 0 to 55 °C |
| Vibration Resistance | 5.9 m/s² |
