Moog minimoog Voyager User Manual

IMPORTANT SAFETY INSTRUCTIONS
WARNING – When using electric products, basic precautions should always be followed, including the following:
1) Read all the instructions before using the product.
2) Do not use this product near water – for example, near a bathtub, washbowl, kitchen sink, in a wet basement, or
near a swimming pool or the like.
3) This product should be used only with a cart or stand that is recommended by the manufacturer.
4) This product, in combination with an amplifier and headphones or speakers, may be capable of producing
sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume
level or at a level that is uncomfortable. If you experience any hearing loss or ringing in your ears, you should consult
an audiologist.
5) The product should be located so that its location does not interfere with its proper ventilation.
6) The product should be located away from heat sources such as radiators, heat registers, or other products that
produce heat.
7) The product should be connected to a power supply only of the type described in the operating instructions or as
marked on the product.
8) The power-supply cord of the product should be unplugged from the outlet when left unused for a long period of
time.
9) Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.
10) The product should be serviced by qualified personnel when:
a) The power-supply cord or the plug has been damaged; or
b) Objects have fallen, or liquid has been spilled onto the product; or
c) The product has been exposed to rain; or
d) The product does not appear to operate normally or exhibits a marked change in
performance; or
e) The product has been dropped or the enclosure damaged.
11) Do not attempt to service the product beyond that described in the user-maintenance instructions. All other
servicing should be referred to qualified service personnel.
DANGER: INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS: Do not open the
chassis. There are no user serviceable parts inside. Refer all servicing to qualified personnel only.
GROUNDING INSTRUCTIONS:
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance
for electrical current to reduce the risk of electric shock. This product is equipped with a cord having an equipment
grounding connector and a grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
DANGER – Improper connection of the equipment-grounding connector can result in a risk of electric shock. Check
with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not
modify the plug provided with this product – if it will not fit in the outlet, have a proper outlet installed by a qualified
electrician.
SAVE THESE INSTRUCTIONS

Moog minimoog Voyager Specifications

General

Brand	Moog
Model	minimoog Voyager
Category	Synthesizer
Language	English

Summary

Important Safety Instructions

Safety Precautions and Warnings

General safety precautions, risk of fire/shock, and essential grounding instructions for safe operation.

Minimoog Voyager Introduction

Product Overview and Design

Overview of the minimoog Voyager synthesizer, its design, and its capabilities.

Getting Started and Initial Setup

Setup, Connections, and Warranty

Steps for unpacking, identifying accessories, warranty registration, and connecting AC power.

Basic Operation

Power Up and Audio Output

Procedures for powering on the Voyager, connecting to amplifiers/headphones, and starting to play.

Fundamentals of Analog Synthesis

Sound Properties and Synthesis Basics

Explains frequency, amplitude, harmonics, and core synthesis components like oscillators and filters.

Control Voltage and Modulation

Explains control voltages (CVs) and modulation techniques for shaping sound parameters.

Envelope Generators and LFOs

Details envelope generators (ADSR) for shaping sound over time and LFOs for modulation.

Minimoog Voyager Features

Front and Back Panel Overview

Overview of the front and back panels, detailing controls, connections, and signal flow.

Voyager Components: Mixer

Mixer Function and Sound Sources

Describes the Mixer's role in combining sound sources like oscillators, noise, and external audio.

Voyager Components: Oscillators

Oscillator Overview and Tuning Controls

Introduces the analog VCOs, their tuning stability, and controls for octave and frequency.

Voyager Components: Filters

Filter Basics and Control Parameters

Explains filters, cutoff frequency, types, and control parameters like Spacing and Resonance.

Voyager Components: Envelopes

Envelope Generator Basics (ADSR)

Explains envelope generators shaping sound over time with Attack, Decay, Sustain, and Release parameters.

Voyager Components: Modulation, LFO, Keyboard, Touch Surface

Modulation Busses, LFO, and Keyboard Controls

Covers Modulation Busses, LFO functionality, keyboard controls, and the touch surface controller.

Voyager Components: Back Panel and Output

Back Panel Connections and Main Output

Details back panel jacks, accessory ports, and main audio output controls like Master and Headphone Volume.

User Interface and Software

Interface and Operating Modes

Describes the LCD interface, its initial message, and the three operating modes: MASTER, EDIT, and PANEL.

Edit Mode Functions

Details Edit Mode functions like RECALL, REAL PANEL CONTROL, PITCH BEND AMT, and PRESET NAME.

Preset Management: Naming and Saving

Details assigning names to presets and saving current settings to memory locations.

Panel Mode Operation

Describes accessing presets and performance functions in Panel Mode, including Quick Mode and Parameter Display.

MIDI Implementation

MIDI Communication Protocol

Details the Voyager's MIDI implementation, including transmitted and responded messages.

Appendices

Caring for Your Voyager

Instructions for cleaning the Voyager cabinet and handling maintenance.

Factory Presets and MIDI Chart

Provides a list of factory presets and the MIDI implementation chart.