Morningstar SunSaver SS-10L Quick Start Guide

Quick Start Guide
14
Specifications:
Battery Type Selection:
SS‐6/6L
NominalSystemVoltage 12V
BatteryVoltageRange 6Vto15V
MaximumSolarInputVoltage 30V
MaximumSolarCurrent 6.5A
MaximumLoadCurrent 6A
©2021MorningstarCorporation.AllRightsReserved. MP‐003293SS‐PWM(Gen3)QSG(3/4/2021)RevC01
In the Box:
Mounting
Screws(x4)
Tools Required:
— #2PhilipsScrewdriver
— 3/16(5mm)&3/32"(2.5mm)FlatheadScrewdriver
— Drillwitha3/32"(2.5mm)bit
— Multimeter
Important Safety Information:
WARNING: Shock Hazard
TheSunSaversolarcontrollermustbe
installedbyaqualifiedtechnicianin
accordancewiththeelectrical
regulationsofthecountryofinstallation.
WARNING: Shock Hazard
ThisunitisnotprovidedwithaGFDI
device.Thischargecontrollermustbe
usedwithanexternalGFDIdeviceas
requiredbytheArticle690ofthe
NationalElectricalCodeforthe
installationlocation.
IMPORTANT: READtheSunSaver
InstallationManualforsafetyand
regulatoryinformation,instructionson
configurationandoperation,and
warrantyinformation.
Scan QR Code to go
directly to the
SunSaver Installation
Manual and warranty
information online.
Contact Information:
TechnicalSupport:Support.morningstarcorp.com
Phone:1‐215‐321‐4457
SunSaverSolarChargeController
WarrantyRegistration:https://www.morningstarcorp.com/product‐registration/
BatterySelectJumper
INSERTED
Battery
Select
Jumper
REMOVED
SOLAR CONTROLLER
SS‐10/10L
6Vto15V
10A
10A
SS‐20L
20A
20A
BATTERY SET POINTS
Set Point
AbsorptionVoltage
FloatVoltage
TimeuntilFloat
EqualizeVoltage
12-volt
14.1V
13.7V
3hours
N/A
EqualizeDuration(hours)
EqualizeCalendar(days)
MaximumRegulationVoltage*
N/A
N/A
LowVoltageDisconnect(LVD)
LowVoltageReconnect(LVR)
HighVoltageDisconnect(HVD)
HighVoltageReconnect(HVR)
StartupLVD
InstantLVD
24-volt
29.2V
27.4V
29.8V
*Nottemperaturecompensated.15V@12Vnominal,30V@24Vnominal.
12-volt
14.6V
13.7V
14.9V
3hours
28days
24-volt
28.2V
27.4V
15.0V 30.0V15.0V30.0V
AbsorptionDuration 3hours
Sealed Flooded
11.5V 23.0V11.5V23.0V
12.6V 25.2V12.6V25.2V
14V 28V14V28V
11.7V 23.4V11.7V23.4V
10.0V 20.0V10.0V20.0V
15.3V 30.6V15.3V30.6V
30V 60V
12V 24V12V 24V
30V 60V
6Vto30V 6Vto15V 6Vto30V
For Sealed Batteries: For Flooded Batteries:
IMPORTANT:
PulseWidthModulation(PWM)Chargingversus
SlowSwitchingCharging
SeetheSunSaverInstallationManualfordirections
forchangingtheregulationfromPulseWidth
Modulation(PWM)chargingtoSlowSwitching
charging.
SlowSwitchingregulationlimitstheswitching
frequencyto10hz.(maximum),whichcan
eliminatenoiseissuesinsomesystems.
PWMchargingisselectedbydefault.
To Install the Terminal Cover (requiredbyUL/ETLlistedsystems):
1. Removethetwolowerscrewsfrom
thefaceplate.
2. AligntheTerminalCoverover
theholes.
3. InsertthescrewsremovedinStep1and
hand‐tightenusingcarenottoover‐tighten.
IMPORTANT:
TheSunSaverchargingalgorithmiscompatible
withlead‐acidorNiCdbatteries.NiMH,Li‐ion,
andotherbatterychemistriesarenotcompatible
withtheSunSaverchargingalgorithm.
TerminalCover
SS‐6
SS‐6L*
SS‐10
SS‐10L*
SS‐20L*
SunSaver Models:
*Automatic Load Control:
LoadControlautomatically
disconnects
and reconnects system loads based upon
the Low Voltage Disconnect (LVD) and
Low Voltage Reconnect (LVR) voltage
thresholds.
The LVD and LVR thresholds are listed on
Page 4 of this Quick Start Guide.
ThisfeatureisexclusivetomodelsSS‐6L,
SS‐10L,andSS‐20Lonly.

Morningstar SunSaver SS-10L Specifications

General

Brand	Morningstar
Model	SunSaver SS-10L
Category	Controller
Language	English