How do I fix a touchscreen that needs to be calibrated on my Mortara ELI 280?
To calibrate the touchscreen on your Mortara Medical Equipment, disconnect the AC power cable from the wall outlet and depress the On/Off button for >7 seconds. Plug the AC power cord back into the wall outlet and follow the instructions on the display. If the problem persists, contact Mortara Technical Support.
What to do if my Mortara ELI 280 Medical Equipment touchscreen needs to be calibrated?
If the touchscreen on your Mortara Medical Equipment needs to be calibrated, repeat the touchscreen calibration procedure.
What to do if my Mortara ELI 280 Medical Equipment established connection, then failed?
If your Mortara Medical Equipment connection started but failed, attempt to reconnect.
What to do if my Mortara ELI 280 Medical Equipment displays DICOM order storage failed?
If your Mortara Medical Equipment displays 'DICOM order storage failed', the directory might be full. Mark records for deletion or delete records.
What to do if my Mortara ELI 280 unable to print and paper queue mark not detected as expected?
If your Mortara Medical Equipment is unable to print because the paper queue mark is not detected as expected, add paper, manually advance the page evenly past the closure point of the writer, close the writer cover, and press STOP.
What to do if my Mortara ELI 280 Medical Equipment has possible incorrect version of ELI Link?
If your Mortara Medical Equipment indicates a possible incorrect version of ELI Link, install the latest version.
What does pressing SYNC key do on Mortara ELI 280 Medical Equipment?
When pressing the SYNC key on Mortara Medical Equipment, enable SYNC MODE and/or set SYNC MEDIA in configuration.
What to do if my Mortara Medical Equipment is not configured for DICOM?
If a DICOM communication was attempted, but your Mortara Medical Equipment is not configured for DICOM, configure the system to DICOM and reboot.
What to do if my Mortara ELI 280 says 'No available memory. ECG data too noisy to store'?
If your Mortara Medical Equipment displays 'No available memory. ECG data too noisy to store', press stop to continue. Then, transmit or mark records for deletion in the directory. Correct the noise issue and attempt acquisition/storage again.
What to do if my Mortara ELI 280 Medical Equipment unable to transmit ECG?
If your Mortara Medical Equipment is unable to transmit ECG, check the phone line. Ensure the site number is valid and try again.
Details the warranty coverage for products and consumables, including time periods.
Provides general safety advice and specific warnings related to device operation.
Details safety practices for electrical connections, patient leads, and defibrillation.
Step-by-step instructions for cleaning and disinfecting the device and its components.
Specifies the medical conditions and populations for which the device is indicated.
Provides an overview of the device's capabilities and diagrams of its components.
A comprehensive list of the ELI 280's technical features and specifications.
Steps for initial device setup and calibrating the touchscreen display.
Guides on powering the device on/off and understanding battery status.
Procedures for preparing the patient and their skin before ECG acquisition.
Guidance on correct electrode placement and a hookup summary table.
Methods for entering patient demographics: manual, stored, orders, and barcodes.
Instructions for setting up the ECG display format, speed, gain, and filter.
Procedures for acquiring ECGs, STAT ECGs, and understanding notification messages.
General ECG transmission methods and how to test RF signal strength.
Instructions for connecting to a Local Area Network and interpreting status LEDs.
Procedures for connecting to a Wireless Local Area Network and configuring security.
Methods for transferring data using USB memory sticks and PC connections.
Information on accessing and searching the ECG directory for patient records.
Instructions for performing a Patient Demographic Query using search tools.
Information on device passwords and procedures for setting or changing them.
General| ECG Type | 12-Lead |
|---|---|
| Number of Leads | 12 |
| Type | Resting ECG |
| Channels | 12 |
| Display | LCD |
| Connectivity | USB, Ethernet |
| Paper Size | A4 |
| Sampling Rate | 1000 samples per second per channel |
| Digital Resolution | 5 μV |
| Power Supply | AC 100-240V, 50/60Hz |
To Next Page
