To Next Page
S
Sherri KeithSep 23, 2025
What to do if Mortara ELI 280 Medical Equipment shows Lead I and II artifact?
- MMichelle LawsonSep 23, 2025
If the Mortara Medical Equipment displays artifact in Lead I and II, check the RA electrode.
What to do if Mortara ELI 280 Medical Equipment shows Lead I and II artifact?
If the Mortara Medical Equipment displays artifact in Lead I and II, check the RA electrode.
What to do if my Mortara ELI 280 is not responding?
If your Mortara Medical Equipment is not responding, press and hold the On/Off button for 10 seconds. Note that re-entry of date and time will be required after performing this action.
How to fix lead fail on Mortara ELI 280 Medical Equipment?
To fix a lead fail on your Mortara Medical Equipment, check the limb leads and correct any faulty lead(s).
What to do if my Mortara Medical Equipment unable to acquire ECG or unable to print?
If your Mortara Medical Equipment is unable to acquire ECG or unable to print, charge the battery with AC power.
What to do if Mortara ELI 280 Medical Equipment shows Lead I and III artifact?
If the Mortara Medical Equipment shows artifact in Lead I and III, check the LA electrode.
What to do if my Mortara Medical Equipment unable to connect with LAN with crossover cable?
If your Mortara Medical Equipment is unable to connect with LAN using a crossover cable, implement a hub instead of a crossover cable.
How do I fix a touchscreen that needs to be calibrated on my Mortara ELI 280?
To calibrate the touchscreen on your Mortara Medical Equipment, disconnect the AC power cable from the wall outlet and depress the On/Off button for >7 seconds. Plug the AC power cord back into the wall outlet and follow the instructions on the display. If the problem persists, contact Mortara Technical Support.
How to fix file not successfully transmitted via LAN on Mortara ELI 280?
If a file was not successfully transmitted via LAN on your Mortara Medical Equipment, check the share permissions on the host device.
What does pressing SYNC key do on Mortara ELI 280 Medical Equipment?
When pressing the SYNC key on Mortara Medical Equipment, enable SYNC MODE and/or set SYNC MEDIA in configuration.
What to do if my Mortara ELI 280 says 'No available memory. ECG data too noisy to store'?
If your Mortara Medical Equipment displays 'No available memory. ECG data too noisy to store', press stop to continue. Then, transmit or mark records for deletion in the directory. Correct the noise issue and attempt acquisition/storage again.
Details the warranty coverage for products and consumables, including time periods.
Provides general safety advice and specific warnings related to device operation.
Details safety practices for electrical connections, patient leads, and defibrillation.
Step-by-step instructions for cleaning and disinfecting the device and its components.
Specifies the medical conditions and populations for which the device is indicated.
Provides an overview of the device's capabilities and diagrams of its components.
A comprehensive list of the ELI 280's technical features and specifications.
Steps for initial device setup and calibrating the touchscreen display.
Guides on powering the device on/off and understanding battery status.
Procedures for preparing the patient and their skin before ECG acquisition.
Guidance on correct electrode placement and a hookup summary table.
Methods for entering patient demographics: manual, stored, orders, and barcodes.
Instructions for setting up the ECG display format, speed, gain, and filter.
Procedures for acquiring ECGs, STAT ECGs, and understanding notification messages.
General ECG transmission methods and how to test RF signal strength.
Instructions for connecting to a Local Area Network and interpreting status LEDs.
Procedures for connecting to a Wireless Local Area Network and configuring security.
Methods for transferring data using USB memory sticks and PC connections.
Information on accessing and searching the ECG directory for patient records.
Instructions for performing a Patient Demographic Query using search tools.
Information on device passwords and procedures for setting or changing them.
General| ECG Type | 12-Lead |
|---|---|
| Number of Leads | 12 |
| Type | Resting ECG |
| Channels | 12 |
| Display | LCD |
| Connectivity | USB, Ethernet |
| Paper Size | A4 |
| Sampling Rate | 1000 samples per second per channel |
| Digital Resolution | 5 μV |
| Power Supply | AC 100-240V, 50/60Hz |
