What to do if the sweep square is not going across the screen on my Mortara Medical Equipment?
If the sweep square is not going across the screen but the time is advancing on your Mortara Medical Equipment, plug the AM12/AM15E into the socket marked ECG.
Why paper does not advance correctly on Mortara Medical Equipment?
If the paper does not advance correctly on your Mortara Medical Equipment: Verify it is the correct paper. Verify paper is properly loaded with the cueing mark in the lower left corner. Open the paper door, remove the paper and make sure there are no sheets of cardboard under the paper. Pull ½ sheet of paper out and securely close the door. You should hear a loud click. Press RHY and press Done after a couple seconds. Paper should advance to the end of the page and stop.
What to do if ECG data is too noisy to store and directory is full on Mortara Medical Equipment?
If your Mortara Medical Equipment gives noisy ECG data that's too noisy to store and the directory is full, correct the noise and try acquisition/storage again. You may also need to erase records and check the Delete rule.
What to do if WLAN failed to initialize on Mortara Medical Equipment?
If the WLAN failed to initialize on your Mortara Medical Equipment, contact Mortara Technical Service.
Why does the paper not advance and make a grinding noise on my Mortara Medical Equipment?
If the paper does not advance and there is a grinding noise on your Mortara Medical Equipment, make sure you are using the correct Mortara paper. Open the paper door and remove the paper to make sure there is no cardboard at the bottom of the paper. Inspect the paper tray to see if there is any broken plastic. Bring out ½ sheet of paper and close the door completely. Go into the Service menu and press Writer Test. If the paper does not advance and it is grinding, press on the lower right corner of the paper door. If the noise goes away, there is broken plastic someplace of the gearbox is out of alignment.
What to do if WLAN module failed to get an address from DHCP on my Mortara Medical Equipment?
If the WLAN module on your Mortara Medical Equipment fails to get an address from DHCP, contact your Networking/IT to see if MAC authentication is required. Verify the request is getting to the DHCP server. You may also need to contact Mortara Technical Service.
How to troubleshoot 'Lead fail' on Mortara Medical Equipment?
To resolve a 'Lead fail' on your Mortara Medical Equipment, ensure the lead and electrode connection is secure. Replace faulty electrode patches or lead wires if necessary. Also, consider patient prep steps.
What to do if the screen does not turn on when the lid is lifted on Mortara Medical Equipment?
If the screen does not turn on when the lid is lifted on your Mortara Medical Equipment, press the power button once. If the Mortara logo does not appear within 10 seconds, press and hold the power button for more than 30 seconds.
What to do if my Mortara Medical Equipment will not power on?
If your Mortara Medical Equipment will not power on, disconnect the AC power cable from the wall outlet and depress the On/Off button for more than 30 seconds. Then, plug the AC power cord back into the wall outlet and follow the instructions on the display. If the problem persists, contact Mortara Technical Support.
How to exit Standby Mode on Mortara Medical Equipment?
If your Mortara Medical Equipment is in Standby Mode, press the On/Standby button to return to active use.
General| Type | Electrocardiograph |
|---|---|
| Number of Channels | 12 |
| Battery Life | Up to 8 hours |
| Display | LCD |
| Connectivity | USB |
| Keyboard | Alphanumeric |
| Data Storage | Internal memory |
| Power | Rechargeable battery |
| Sampling Rate | 40, 000 samples/second/channel used for pacemaker spike detection; 1, 000 samples/second/channel used for recording and analysis |
Critical safety warnings to prevent injury or damage.
Important cautions for safe device operation and maintenance.
Guidelines for electromagnetic emissions and intended environment.
Guidelines for electromagnetic immunity and intended environment.
Steps for initial device setup and configuration.
Instructions for configuring AMxx and WAM wireless acquisition modules.
Overview of configurable settings accessible to all users.
Instructions on powering the device using AC power or battery.
Steps for preparing the patient and attaching electrodes for ECG acquisition.
Methods for entering patient demographic information.
Procedure for manually entering patient data.
Steps for acquiring and printing ECGs using WAM or AMxx modules.
Guidance for electrode placement errors and screen notification messages.
How critical test results are identified and notified to the user.
Procedures for printing rhythm strips and acquiring STAT ECGs.
Information on transmitting ECG records via LAN or WLAN.
Configuring AC filter, ECG filters, interpretation, reasons, and CTR.
Steps for configuring LAN connection parameters for network transmission.
Steps for configuring WLAN connection parameters for wireless transmission.
Setting and managing administrator and technician passwords.
Troubleshooting guide for system-level issues and LCD messages.
Troubleshooting guide for ECG acquisition and artifact issues.
Troubleshooting guide for ECG transmission and connectivity problems.
Troubleshooting guide for display-related issues.
To Next Page
