MSD 6014 User Manual

MSD • WWW.MSDPERFORMANCE.COM • (915) 855-7123 • FAX (915) 857-3344
ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product
will help if there is ever a warranty issue with your product and helps the MSD R&D team create
new products that you ask for! Go to www.msdperformance.com/registration.
MSD LS Ignition Control
PN 6014/60143
Parts Included:
1 – LS Ignition Controller, PN 6014
1 – Main Wiring Harness
1 – Crank/Cam Pigtail 24x
1 – Crank/Cam Pigtail 58x
1 – Sub Harness
1 – USB Cable
1 – Mounting Kit
1 – MSDView USB
WARNING: During installation, disconnect the battery cables. When disconnecting, always re-
move the negative cable rst and install it last.
Note: Solid core spark plug wires cannot be used with an MSD Ignition Control.
OPERATION
The MSD 6014 LS Ignition controller works with 24x/1x, 58x/4x and 58x/1x crank/cam congura-
tions. It auto detects the correct conguration based on the reluctor wheel pattern, so there is no
need to select one. It provides six pre-programmed (non-editable) timing tables for stock engines,
three customizable 3-D tables and one customizable timing plot. The desired table/plot is selected
on the y using the rotary dial. The customizable tables and plot can be programmed via MSDView.
The LS Ignition controller includes a built-in 2.5 Bar MAP sensor that can be used with Naturally
Aspirated or boosted applications. This allows for timing advance or retard based on the intake
manifold pressure.
8Mb of internal data logging is also included so you can setup, record and review runs at the track.
Note: It is recommended, that you install and run MSDView software while connected to the unit to
perform the base settings. The unit can be powered off of USB, so this can be done from a
desktop or laptop and does not require an external power source.
Optional Accessories (Purchased Separately):
LS Coolant Temp Sensor, GM PN 12608814
PN 2279 - 24x Crank/4x Cam

MSD 6014 Specifications

General

Product Name	MSD 6014
Category	Controller
Type	Ignition Control
Rev Limiter	Yes
Voltage	12 V
Input Voltage	12 V

Summary

Product Operation and Features

Controller Operation Overview

Explains auto-detection, pre-programmed and customizable timing tables, MAP sensor, and data logging.

Wiring and Connections

Wiring Features and Pinouts

Details pin functions for various connectors, including main harness, sensors, and coils.

Connector Pin Descriptions

Provides detailed pin functions for the 16-Pin and 10-Pin connectors.

Installation and Mounting

Mounting Instructions

Guidance on securely mounting the ignition controller in a suitable location.

Software Configuration and Management

MSDView Software Installation

Instructions for installing and using the MSDView software for configuration.

Programmable Settings

Details adjustable settings like Rev Limiters, Coil Type, and Idle Timing Control.

Timing Table Configuration

Explains various timing tables (Custom, Truck, LS1, etc.) and their adjustment.

Temperature-Based Timing Adjustments

Details how engine coolant temperature affects ignition timing.

Step Retard Configuration

Describes configuring the Step Retard input for timing adjustments with a power adder.

Launch Retard Settings

Configuration of ignition timing adjustments for launch control.

Data Acquisition System

Overview of the 8MB data logging system, channels, and monitors.

Troubleshooting and Support

System Alerts and Faults

Explains various fault codes and alerts indicating potential system issues.

Warranty Service Information

Procedures for obtaining warranty service or returning the product.

Limited Warranty Policy

Details the one-year limited warranty against defects in material and workmanship.