mspa MONT BLANC P-MB04 User Manual (English)

Questions and Answers:

M
Michael CooperAug 12, 2025
Why is my mspa MONT BLANC P-MB04 Hot Tub not heating properly?
- W
  wbuckleyAug 12, 2025
  If your MSpa Hot Tub isn't heating properly, there are a few things you can check. First, make sure the temperature isn't set too low and adjust it to a higher setting. Also, a dirty filter cartridge can cause heating issues, so clean or replace it. Ensure the water level is at least at the minimum line; if not, add more water. If these steps don't resolve the issue, it could indicate a heater or filter pump failure, in which case you should contact the MSpa Service Center.
K
Krista HallAug 16, 2025
How to clean the water in my MSpa Hot Tub?
- S
  Steven Davis MDAug 16, 2025
  If the water in your MSpa Hot Tub isn't clean, the first step is to change the water, especially if it has been used for an extended period. Increase the filtration frequency. Regularly clean or replace the filter cartridge. Ensure you are following the chemical manufacturer's instructions for water maintenance.
M
Melissa DuffyAug 20, 2025
How to fix no display on the MSpa Hot Tub control panel?
- C
  Christopher MillerAug 20, 2025
  If there's no display on your MSpa Hot Tub control panel, begin by checking the power source to ensure it's working. Next, reset the PRCD. If the PRCD is broken or the control panel is still not displayed after pressing the reset button, contact the MSpa Service Center. Finally, check the digital cable connection, ensuring the pins inside are well connected.
D
Derrick MooreAug 25, 2025
What to do if the filter pump does not work on my mspa MONT BLANC P-MB04?
- J
  Joseph LeonAug 25, 2025
  If the filter pump on your MSpa Hot Tub isn't working, the first thing to check is the filter itself. It might be stuck due to dirt or other objects. Clean or replace the filter cartridge. If the problem persists, it may indicate a filter system failure, and you should contact the MSpa Service Center.
C
Casey ButlerAug 27, 2025
What to do if my mspa MONT BLANC P-MB04 loses air pressure?
- C
  Catherine MirandaAug 27, 2025
  If your MSpa Hot Tub is losing air pressure, first check the air valves to ensure they are secure. If necessary, replace them. Also, inspect the spa tub for holes or splits by applying soap water to the seams; bubbling indicates a leak. Clean and dry the leaking area before applying the repair patch.
S
Samantha OdonnellAug 31, 2025
Why is the bubble air blower not working on my mspa MONT BLANC P-MB04?
- G
  Gregory MorenoAug 31, 2025
  If the bubble air blower on your MSpa Hot Tub isn't working, check the digital cable connection, ensuring the pins inside are well connected. If the blower has auto-off after 10 minutes, wait for 10 minutes. Ensure the water level is at the minimum water line and add more water if needed. For other potential issues such as a unidirectional threshold not being open, control panel failure, or a one-way valve being blocked, contact the MSpa Service Center.
C
Christina JohnsonSep 4, 2025
Why is my mspa MONT BLANC P-MB04 leaking?
- B
  Brittany HendersonSep 4, 2025
  If your MSpa is leaking, start by checking the spa inlet/outlet connections to ensure they are securely tight. If the leak persists, inspect the spa pool body for leaks and repair with the repair kit material. If the drainage valve is not closed completely, contact the MSpa Service Center.
K
Kyle JohnsonSep 7, 2025
What causes my mspa MONT BLANC P-MB04 to be in an abnormal shape?
- W
  williamsjacobSep 8, 2025
  If your MSpa tub is in an abnormal shape, it may be due to extra air pressure from strong sunshine. Check the air pressure and release some air if necessary. During hot weather, it is recommended to check if it is necessary to release some air to avoid any possible damage to the spa pool.

mspa MONT BLANC P-MB04 Specifications

General

Model	MONT BLANC P-MB04
Category	Hot Tub
Jets	118 Air Jets
Heater	1500W
Massage Air Blower	600W
Heating Power	1500W
Control Panel	Integrated Digital Control Panel
Voltage	220-240V
Frequency	50Hz
Capacity	4 People
Water Capacity	700 Liters
Heating System	Electric
Temperature Range	20-42°C
Material	Rhino-Tech Reinforced PVC
Control System	Digital Control Panel
Weight	23 kg (without water)
Color	White
Warranty	12 months
Heat Increasing Rate	1.5-2.5°C/hour