mspa P-CA069 User Manual (English)

Questions and Answers:

O
ogriffithAug 14, 2025
Why is my mspa P-CA069 not heating properly?
- M
  Mr. Thomas MartinezAug 14, 2025
  Your MSpa hot tub might not be heating properly due to several reasons: * The set temperature could be too low, in which case you should set a higher temperature. * A dirty filter cartridge can prevent proper heating. Clean or replace the filter cartridge. * If the water level is below the minimum line, add more water. If these steps don't resolve the issue, it may be due to a heater or filter pump failure, requiring professional assistance.
T
Tracy HughesAug 17, 2025
What to do if there is no display on the wired controller of my mspa Hot Tub?
- J
  jenniferwolfeAug 17, 2025
  If there's no display on your MSpa hot tub's wired controller, consider the following: * Check the power supply to ensure it's working. * Reset the PRCD (Portable Residual Current Device) by following the PRCD Testing section to resolve a potential trip. If the issue persists, the PRCD might be broken, or there could be an internal problem with the control panel, which would require contacting the MSpa Service Center.
J
Jennifer HallAug 21, 2025
Why doesn't the bubble air blower work on my mspa Hot Tub?
- K
  krodriguezAug 21, 2025
  The bubble air blower on your MSpa hot tub might not be working for these reasons: * It may have automatically turned off after 10 minutes; wait for 10 minutes before restarting. * If the inflation knob is in the position, turn it to and then try turning on the bubble button again. If the issue persists, there might be a problem with the unidirectional threshold or control panel, requiring assistance from the MSpa Service Center.
S
Samuel WashingtonAug 25, 2025
Why is my MSpa Bathtub not heating properly?
- M
  Morgan GonzalezAug 25, 2025
  Your MSpa Bathtub might not be heating properly due to several reasons. The water level might be below the minimum line, so add more water. The temperature setting could be too low, so increase it. Alternatively, the filter cartridge might be dirty, requiring cleaning or replacement.
M
Michael HughesAug 27, 2025
How to fix no display on the wired controller of MSpa Bathtubs?
- L
  larrypenningtonAug 27, 2025
  If there is no display on the wired controller of your MSpa Bathtub, first, check the power supply. If that's not the issue, reset the GFCI. If the GFCI continues to trip, there may be an issue.
L
loganchavezAug 31, 2025
What to do if my MSpa Bathtub is leaking?
- R
  Robert WoodsAug 31, 2025
  If your MSpa Bathtub is leaking, first check the spa inlet/outlet connections and tighten them if they are loose. Also, ensure the drainage valve is completely closed. If the leak persists and appears to be coming from the spa pool body, use the repair kit material to patch the hole.
E
ecruzSep 3, 2025
Why is my MSpa Bathtub losing air pressure?
- D
  Donna WilkinsonSep 3, 2025
  If your MSpa Bathtub is losing air pressure, the air valve may be loose. Inflate the spa until the yellow section of the manometer is pushed out and ensure the valve is tightly screwed. If necessary, replace the valve. Additionally, inspect the spa tub for holes or splits. Apply soapy water to seams; bubbles indicate a leak. Clean and dry the area before applying the repair patch.
D
Dr. Erin JonesSep 6, 2025
How to troubleshoot the bubble air blower on an MSpa Bathtub?
- N
  Nichole CochranSep 7, 2025
  If the bubble air blower on your MSpa Bathtub isn't working, first check if it has auto-off after 10 minutes; if so, wait 10 minutes before restarting. Ensure the inflation knob is in the position before turning the bubble button on again. Also, the filter might be stuck by dirt or other objects, so clean or replace the filter cartridge.
W
Wayne MendozaSep 10, 2025
What causes an MSpa Bathtub to be in an abnormal shape?
- T
  Trevor MaddenSep 10, 2025
  An MSpa Bathtub can develop an abnormal shape due to extra air pressure from strong sunlight. Check the air pressure and release some air if necessary. In hot weather, it's recommended to periodically check and release air to prevent damage.

mspa P-CA069 Specifications

General

Model	P-CA069
Type	Inflatable Hot Tub
Temperature Range	68°F to 104°F
Material	Durable PVC
Water Capacity	930 Liters (245 Gallons)
Weight	Approx. 42 kg (93 lbs) empty