MTD Bolens BL110 - User Manual

PART NO. 769-015756 P00 (1/10)
Insert 10' of 0.080"SplitLine
®
through
hole in top of reel. Pull most of line
through hole until 3"-4" remains.
Wind line tightly in direction of arrow.
Split other end of SplitLine
®
back 6"-7".
Push 6"-7" ends into
0.080" holding slots.
Insert or slide lines into the
eyelets in spool. Insert spring
and reel into spool.
Pull lines firmly to release
from holding slots.
Bend short end and push it
into the other hole. Pull tight.
Bump
Knob
Inner
Reel
Spool
Spring
Press primer bulb 10 times.
Put blue choke lever
in Position 1.
Move blue choke
lever to Position 2.
While continuing to
squeeze the throttle
control, move the blue
choke lever to Position 3.
SQUEEZE and HOLD throttle
control for ALL further steps.
Pull the rope
5 times.
Pull the rope 3 to 5
times to start. Run
engine for 30-60
seconds to warm up.
Continue warming for an
additional 60 seconds.
During this time the unit
may be used.
Crouch in starting
position.
DIDN’T START?
Repeat these instructions.
If engine still fails to start, refer
to the Starting/ Stopping
instructions section of this
manual for additional starting
and troubleshooting information.
Quick Instructions to
Replace SplitLine
®
Trimmer Line
Replacement SplitLine
®
Part #49U0134K953
For single line installation,
refer to Line Installation
section of this manual.
For replacement spool
installation, refer to Installing a
Prewound Reel section of this manual.
Quick Instructions
to Start Engine
For complete instructions, refer to
Starting/ Stopping Instructions section
of this manual.
Quick Instructions to
Assemble Trimmers
For complete instructions, refer to the
Assembly Instructions section of this
manual.
Unscrew bump knob
counterclockwise. Remove
inner reel and spring.
5 X
3 " -4 "
Hold the inner reel in place.
Tighten Bump Knob
clockwise.
IMPORTANT: READ OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES BEFORE OPERATING THE UNIT.
1 Gallon 3.2 oz
40:1
Put D-handle on shaft. Move handle a
minimum 6 inches away from shaft grip.
Insert clamp bolt and tighten the wing nut.
Mix thoroughly in a separate fuel can:
– 3.2 fl. oz. of 2-cycle engine oil
– 1 gallon of unleaded gasoline
Place the unit on a level surface. Fill fuel tank.
NOTE: Do not mix directly in the fuel tank.
Read and understand all instruction, warning and danger labels on the unit.
Min. 6"
Bolt
Slide the slot in the cutting attachment shield onto
the guard mounting bracket and rotate it onto the
shaft. Push the square bolt through the shield and
bracket and thread it with the washer and wing nut.
Guard Mounting
Bracket
Wing
Nut
Washer
Español — Page 9 English — Page 2Français — Page 5
Operator’s Manual
DO NOT RETURN THIS PRODUCT
For Assistance, please call 1-800-800-7310 (U.S.) or 1-800-668-1238 (Canada)
or visit www.mtdproducts.com or www.mtdproducts.ca
NEED HELP? CALL 1–800-800-7310 IN U.S. OR 1–800–668–1238 IN CANADA
BL110
2-Cycle Trimmer

Summary

Quick Instructions to Assemble Trimmers

Quick Instructions to Start Engine

Quick Instructions to Replace SplitLine Trimmer Line

Service Information

Rules for Safe Operation

While Operating

Safety precautions and best practices to follow during operation, including protective gear and handling.

Safety Warnings for Gas Units

Specific safety advice related to gasoline-powered units, covering fuel handling and ignition risks.

Safety and International Symbols

Explanation of safety symbols and warnings used in the manual to highlight potential hazards.

Know Your Unit

Starting;Stopping Instructions

Operating Instructions

Assembly Instructions

Oil and Fuel Information

Maintenance and Repair Instructions

Maintenance Schedule

Schedule for routine maintenance tasks and required procedures for optimal unit performance.

Line Installation

Air Filter Maintenance

Carburetor Adjustment

Replacing the Spark Plug

Cleaning

Storage

Troubleshooting

Engine Will Not Start

Common causes and solutions for an engine that fails to start.

Engine Will Not Idle

Troubleshooting steps for an engine that does not idle correctly.

Engine Will Not Accelerate

Diagnostic information for an engine that hesitates or fails to accelerate.

Engine Lacks Power or Stalls

Reasons for reduced engine power or stalling during operation.

Cutting Head Will Not Advance Line

Solutions for issues where the trimmer line does not extend properly.

Cutting Line Advances Uncontrollably

Troubleshooting for trimmer line that extends excessively or continuously.

Specifications

Manufacturers Limited Warranty

MTD Bolens BL110 Specifications

General

Engine Type	2-cycle
Displacement	25 cc
Weight	12.1 lbs
Type	Straight Shaft
Power Source	Gasoline
Line Diameter	0.080 inches
Cutting Width	16 inches
Cutting Swath	16 inches