To Next Page
S
Susan MorenoAug 28, 2025
What are the possible engine reactions to a red alarm in MTU Engine?
- BbyrdmeganAug 28, 2025
A red alarm may result in an engine stop, power limitation/reduction, speed limitation, or a warning.
What are the possible engine reactions to a red alarm in MTU Engine?
A red alarm may result in an engine stop, power limitation/reduction, speed limitation, or a warning.
What should I do if the coolant pressure at sensor B16 has fallen below limit value 2 in my MTU Engine?
If the coolant pressure at sensor B16 falls below limit value 2, check the relief bore of the engine coolant pump, and check the engine coolant level. Contact Service.
What does it mean if coolant discharges at the intercooler of my MTU Engine?
Coolant discharge at the intercooler, especially a major discharge, suggests that the intercooler is leaking. Contact Service.
What to do if Fuel HP sensor (B48.1) supplies incorrect signal or no signal in MTU Engine?
If the fuel HP sensor (B48.1) supplies an incorrect signal or no signal, check the engine wiring. Contact Service.
What should I do if the coolant temperature at sensor B6.1 has exceeded limit value 2 in my MTU Engine?
If the coolant temperature at sensor B6.1 has exceeded limit value 2, check the operation of the cooler and fan (plant side), and check the engine coolant level. Contact Service.
What to do if the supply voltage of the ECU has exceeded the specified limit value 1 in MTU Engine?
If the supply voltage of the ECU has exceeded the specified limit value 1, check the charging condition of the batteries (plant side), and check the plug connections to the engine governor. Contact Service.
What to do if Lube-oil pressure sensor after filter (B5.1) supplies incorrect signal or no signal in MTU Engine?
If the lube-oil pressure sensor after the filter (B5.1) supplies an incorrect signal or no signal, check the engine wiring. Contact Service.
What causes white exhaust gas from my MTU Engine?
White exhaust gas from the MTU Engine can be attributed to a few reasons: * The engine is not at operating temperature: Run the engine up to operating temperature. * Water in the fuel: Check the fuel system, especially at the fuel prefilter. Drain water and contaminants from the fuel prefilter. * A leaky intercooler: Contact Service.
What to do if the MTU Engine turns on starting but does not fire?
If the MTU Engine turns on starting but does not fire, possible causes include: * Poor rotation by the starter: Charge or replace the battery. * A low or defective battery. * Air in the fuel system: Vent the fuel system. * A defective engine governor: Contact Service.
What causes black exhaust gas from my MTU Engine?
Black exhaust gas from the MTU Engine can be caused by: * A clogged air filter: Check and replace the air filter if necessary. * A defective injector: Check and replace the injector if necessary. * Engine overload: Contact Service.
General safety information and intended use of the product.
Safety rules to follow before and during engine startup and operation.
Safety guidelines for performing maintenance and repair tasks on the engine.
Guidelines for fire safety, environmental protection, and handling of fluids and lubricants.
Detailed description of the engine's systems and components.
Visual overview of the engine with labeled components.
Identification and function of key sensors and actuators on the engine.
Technical specifications for various engine models and configurations.
Provides the overall physical dimensions of the engine.
Procedures for starting and stopping the engine, including manual trials.
How to perform an emergency stop and post-stop procedures.
Routine checks to perform during engine operation.
Reference table linking tasks to maintenance schedule entries.
Guide to diagnosing and resolving common engine problems.
Lists fault messages from the engine governor and their corrective actions.
Information related to SOLAS requirements and installation of shielding.
Tasks related to engine barring, test runs, and component maintenance.
Step-by-step guide to replacing the engine's fuel filter.
Detailed procedure for replacing the engine oil filter.
Procedures for checking, changing, draining, and filling engine coolant.
Inspection and replacement procedures for the engine's belt drive system.
Checks for engine cabling, wiring, and engine governor connections.
Glossary of abbreviations used throughout the manual.
List of special tools required for maintenance and repair tasks.
General