EasyManua.ls Logo

MTX Thunder 6152 - Features; Specifications; Thunder6152 Specifications; Thunder6304 Specifications

MTX Thunder 6152
18 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Features
l
Intelligent Surface Mount Technology
* Patented PWM MOSFET Switching Power Supply (#5,598,325)
* Class A 100% Discrete Driver Circuit Topology
l
New, more reliable high powered transformers
l
Pure N-Channel Design
l
Speaker and low level inputs Inputs on Thunder6152
l
Color-coded wire harness for speaker-level input installation on Thunder6152
* Smart-EngageTM auto turn on for easy integration with factory head units (Thunder6152 only)
l
Input select 2CH /4CH switch on Thunder6304functions as a built-in Y connector
l
Real Ime Computerized Protection Circuit
l
Acoustically Seamless Turn-on/Turn-off (~.a. no noise1
.
Continuously variable/defeatable 12 dB/octave high pass, 24dB/octave mono low pass crossover (variable from 40Hz to 200Hz)
l
Continuously variable/selectable crossover output, switchable from full range/high pass/low pass outputs (Full range only on
Thunder63041
.
EBC Max on Thunder 8302, allows for control of additional subwoofer amps m a daisy chain configuration in low pass mode
l
Contlnuouslv adjustable and defeatable Thunder EQ Bass enhancement circuitry, cantered at 40Hz
* Left and right individually adlustable input sensitivity (ExceptforThunder6304)
- Nickel-plated, heavy duty terminal block type connectors
l
Untque rubber Insulated Iso-FeetTM
l
Buffered. isolated output for daisy chaining multiple amplifiers
Smzcifications
THUNDER6152
RMS Power measured at 12.5 Volts DC
37 5 Watts x 2 mt” a 4 Ohm load with less than 0.1% ThdtN
75 Watts x 2 mm a 2 Ohm load with less than 0.1% ThdtN
150 Watts bridged mt” a 4 Ohm load with less than 0 1% ThdtN
Dynamic Power measured at 144 Volts DC
90 Watts x 2 lmt~ a 4 Ohm load
I65 Watts x 2 mt” a 2 Ohm load
325 Watts bridged mt” a 4 Ohm load
SIgnal to Nose Rat10 >llOdB A-WeIghted
DampIng Factor ,200
, Frequency Responses 20Hz-20kHz f 025dB
MaxImum Input. 8Vrms
Thunder E@ Variable Bass Boost IO-l8dBl centered at 40Hz
Crossover: Variable 40Hzto 200Hz. 12dBioctave high pass,
24dBiactave low pass with m”“” output
Dlmensmns 8.3” x 9.75” x Y (21.lcm x 24.8cm x 5.lcml
1O.r x 3 75” x 2 1” 127 2cm x 24 8cm x 5.3cml Including lsoFeetTM
THUNDER8302
RMS Power measured at 12.5 Volts OC.
75 Watts x 2 into a 4 Ohm load with less than 0 1% ThdtN
150 Watls x 2 into a 2 Ohm load with less than 0 1% ThdtN
300 watts bridged mm a 4 Ohm load with less than 0 1% ThdtN
Oynamlc Power IIHF-202 Standard) measured at 14.4 Volts DC
I20 Waas x 2 mt” a 4 Ohm load
212 Watts x 2 mm a 2 Ohm load
425 Watts bridged mt” a 4 Ohm load
Smnal t” Nmse Ratio ?llOdB A-Wemhted
Oampmg Factor ,200
Frequency Response 20Hz-20kHz f 0 25dB
MaxImum Inpu? 8Vrms
Thunder E@ Variable Bass Boost (0.ISdB) centered at40Hz
Crossover: Variable 40Hz t” 200Hz,lZdBloctave high pass,
24dBioctave low pass wl!h m”n” output
Dlmensmns 9.2n x 9 75” x Y (22 8cm x 22.8cm x 5 lcml
II 5” x 3.75” x 2 I” (29 2cm x 24 8cm x 5.3cm) lncludlng lsoFe@’
THUNDER6304
RMS Power measured at 12.5 Volts DC:
37.5 Watts x 4 mt” a 4 Ohm load with less than 0 3% ThdtN
75 Watts x 4 IntO a 2 Ohm load with less than 0.3% ThdtN
I50 Watts x 2 bridged mta a 4 Ohm load with less than 0.3% ThdtN
Dynamic PowerlIHF-202 Standard) measured at 14.4 Volts DC
90 watts x 4 mto a 4 Ohm load
I65 Watts x 4 mt” a 2 Ohm load
325 Watts x 2 bridged mm a 4 Ohm load
SIgnal to Noise Ratlo: tllOdB A-Welghted
DampIng Factor: ,200
Frequency Response: 20Hz-20kHz i 0 25dB
MaxImum Input: 8Vrms
Thunder Ea: Vanable Bass Boost IO-18dB) centered at 40Hz
Crossover: Vanable 40Hz t” 200Hz, 12dBlactave high pass,
24dBioctave low pass with “0”” output
Dlmensmns. l1.Y x 9.75” x 2” (29.2cm x 24.8cm x 5.lcm)
13.9” x 9.75” x 2 I” (35.3cm x 24.8cm x 5.3~~1 lncludmg lsoFe@

Related product manuals