Multiplex EasyGlider 4 - Parts and Accessories; KIT Components List

25
Parts List KIT EasyGlider 4 # 21 4332
No. Quantity Description Material Dimensions
1 1 Building instructions, KIT Paper 900 x 400 mm
2 1 Complaint processing form Paper DIN A4
3 1 Decal sheet Adhes. lm Ready made
4 1 L.H. fuselage shell ELAPOR Ready made
5 1 R.H. fuselage shell ELAPOR Ready made
6 1 Canopy ELAPOR Ready made
7 1 L.H. wing panel ELAPOR Ready made
8 1 R.H. wing panel ELAPOR Ready made
9 1 Tailplane ELAPOR Ready made
10 1 Fin ELAPOR Ready made
11 1 Fin fairing ELAPOR Ready made
12 1 GRP spar GRP 10 x 10 x 1000 mm
13 1 Foam block, battery retention Foam 30 x 30 x 100 mm
Small parts set
20 2 Hook-and-loop tape, hook Plastic 25 x 60 mm
21 2 Hook-and-loop tape, loop Plastic 25 x 60 mm
22 2 Pre-formed aileron pushrod Metal 1 Ø x 80 mm
23 2 Canopy latch tongue Plastic Ready made
24 2 Canopy latch Plastic Ready made
25 1 Nut Metal M5
26 1 Plastic screw Plastic M5
27 1 Allen key Metal 1.5 A/F
28 4 Grubscrew Metal M3 x 3 mm
29 4 Swivel pushrod connector Metal 6 mm Ø
Plastic parts set
30 1 Tailplane mount Plastic Ready made
31 1 Fin support Plastic Ready made
32 1 Upper tailplane support Plastic Ready made
33 1 Lower tailplane support Plastic Ready made
34 1 Fuselage-mounted rudder hinge Plastic Ready made
35 1 Bottom rudder hinge Plastic Ready made
36 1 Elevator horn Plastic Ready made
37 2 Aileron horn Plastic Ready made
38 2 Fin end-piece Plastic Ready made
39 1 Motor mount Plastic Ready made
40 1 Canopy nger-grip Plastic Ready made
41 2 Cable holder Plastic Ready made
42 2 Fuselage cover plate Plastic Ready made
43 1 L.H. aileron servo fairing Plastic Ready made
44 1 R.H. aileron servo fairing Plastic Ready made
45 2 Spar end-piece Plastic Ready made
46 2 plastic sleeve Plastic 3/2 OD/ID x 20 mm
Rod and tube set
50 2 Pre-formed wire pushrod Metal 0.8 Ø x 875 mm
51 2 Snake inner sleeve Plastic 2/1 OD/ID x 850 mm
52 2 Snake outer sleeve Plastic 3/2 OD/ID x 785 mm
53 2 Aileron spar Metal 3 Ø x 250 mm
54 1 Upper GRP stiffener GRP 1.3 Ø x 680 mm
55 1 Lower GRP stiffener GRP 1.3 Ø x 740 mm
Propeller set
60 1 Taper collet set, complete Metal For 4 mm Ø shaft
61 1 Propeller hub Metal Ready made
62 1 Spinner Plastic Ready made
63 2 Folding propeller blade Plastic 9 x 6‘‘ / 23 x 15 cm
64 1 Plain washer Metal 16/8.4 mm OD/ID
65 1 Shake-proof washer Metal 8.4 mm Ø
66 1 Flat nut Metal M8
67 2 M3 cheesehead screw Metal M3 x 20 mm
68 2 M3 self-locking nut Metal M3
69 1 Mushroom-head screw Metal M2.5 x 12 mm