EasyManuals Logo

NAPCO GEMINI GEMC-32 Programming Instructions

NAPCO GEMINI GEMC-32
52 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #21 background imageLoading...
Page #21 background image
NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2
NAPCO Security Group
Programming Instructions, Volume 2 Page 89
ZONE OPTIONS / ZONES 81-88 (ADDRESS 3002-3088)
ZONE OPTIONS:
1. Select the desired zone option by entering the option
number (1-8) for each selected zone.
2. Enter corresponding option number in address location, in
Binary (Bit) Format.
3. Press U to save.
NOTE: Dark shaded data value box shows option not avail-
able.
ZONE OPTIONS ADDR
ZONES 81 ► 88
Z81 Z82 Z83 Z84 Z85 Z86 Z87 Z88
1 2 3 4 5 6 7 8
Zone Area 1 (Fire) 3044
Zone Area 2 3045
Zone Area 3 3046
Zone Area 4 3047
Zone Area 5 3048
Zone Area 6 3049
Zone Area 7 3050
Zone Area 8 3051
Reserved 3052
Reserved 3053
Zone Anding Group 1 3054
Zone Anding Group 2 3055
Zone Anding Group 3 3056
Zone Anding Group 4 3057
Zone Anding Group 5 3058
Zone Anding Group 6 3059
Zone Anding Group 7 3060
Zone Anding Group 8 3061
Interior 1 Bypass 3062
Interior 2 Bypass 3063
Keypad Sounder on Alarm 3064
Ext Fire Output 1 3065
Ext Fire Output 2 3066
Ext Fire Output 3 3067
Ext Fire Output 4 3068
Ext Fire Output 5 3069
Ext Fire Output 6 3070
Ext Fire Output 7 3071
Ext Fire Output 8 3072
Reserved 3073
Reserved 3074
Carbon Monoxide 3075
Verification (Fire) 3076
Waterflow (Fire) 3077
Supervisory 3078
Monitor Zone 3079
NAC A 3080
NAC B 3081
NAC C 3082
NAC D 3083
Reserved 3084
Reserved 3085
Chime 2 3086
Delayed Trip 1 3087
Delayed Trip 2 3088
ZONE OPTIONS ADDR
ZONES 81 ► 88
Z81 Z82 Z83 Z84 Z85 Z86 Z87 Z88
1 2 3 4 5 6 7 8
Priority Zone 3002
Priority / Bypass 3003
AutoBypass 3004
Selective Bypass 3005
Keyswitch Arming 3006
AutoBypass Re-entry 3007
Pre-Alarm Warning 3008
Never Arm 3009
24-Hour Protection 3010
Burg Bell 3011
Pulse Burg Bell 3012
Burg PGM2 3013
Burg Relay 3014
Burg PGM1 3015
Exit/Entry #1 3016
Exit/Entry #2 3017
Exit/Entry Follower 3018
Auto Reset 3019
Swinger Shutdown 3020
Chime Zone 3021
Abort Delay 3022
Power-Up Delay 3023
Day Zone/Trouble Open 3024
Day Zone/Trouble Short 3025
Alarm on Day Zone/Trouble
3026
Report Alarm Tel1 3027
Rpt Alm Restore Tel1 3028
Report Trouble Tel1 3029
Rpt Tbl Restore Tel1 3030
Reserved 3031
Reserved 3032
Reserved 3033
Reserved 3034
Report Alarm Tel3 3035
Rpt Alm Restore Tel3 3036
Report Trouble Tel3 3037
Rpt Tbl Restore Tel3 3038
No EOL Resistor 3039
Sensor Watch 3040
Trouble on Open 3041
Trouble on Short 3042
Trouble on Night Open 3043
FOOTNOTES AND SYMBOLS FOR TABLES
A
2-wire smoke detectors only available for zones 1-8 or utilizing
FWC-FSLC-CZM on SLC loop. See Installation Instructions
(WI1653) for more details.
B
If Fire Alarm Verification is selected, then Fire must also be
selected.
C
When the Easy Program Menu is used, these features are
enabled by default (for new panels or after a Cold Start
(address 8179)). Zone Area 1 is enabled for the first 8 zones
only, by default.
D
Disable Auto-Reset on non-Fire zones for SIA CP-01 installa-
tions.

Other manuals for NAPCO GEMINI GEMC-32

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NAPCO GEMINI GEMC-32 and is the answer not in the manual?

NAPCO GEMINI GEMC-32 Specifications

General IconGeneral
BrandNAPCO
ModelGEMINI GEMC-32
CategoryControl Panel
LanguageEnglish

Related product manuals