Napoleon 9500 series User Manual

IOM
W415-0973 / B / 08.28.13
UM
PG
57
$10.00
INSTALLER: PLEASE FAMILIARIZE YOURSELF WITH VENTING/DRAINING SECTIONS OF
THIS MANUAL BEFORE PROCEEDING WITH THE INSTALLATION. LEAVE
THIS MANUAL WITH THE APPLIANCE FOR FUTURE REFERENCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
INSTALLATION AND
OPERATING INSTRUCTIONS
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonheatingandcooling.com • ask@napoleonheatingandcooling.com
SAFETY INFORMATION
ELECTRICAL SHOCK, FIRE OR
EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death or
property damage.
Improper servicing could result in
dangerous operation, serious injury, death
or property damage.
- Installation and service must be performed by a
qualifi ed installer, service agency or the gas supplier.
- Before servicing, disconnect all electrical power to
furnace.
- When servicing controls, label all wires prior to
disconnecting. Reconnect wires correctly.
- Verify proper operation after servicing.
- Do not store or use gasoline or other fl ammable
vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the fi re
department.
!
WARNING
!
Patent Pending
MANUFACTURER RESERVES THE RIGHT TO DISCONTINUE, OR CHANGE
AT ANY TIME, SPECIFICATIONS OR DESIGNS WITHOUT NOTICE AND
WITHOUT INCURRING OBLIGATIONS.
H1.13
CERTIFIED TO ANSI Z21.47b / CSA 2.3b-2008
9500 SERIES
SINGLE STAGE MULTI POSITION HIGH EFFICIENCY
(CONDENSING) FORCED AIR GAS FURNACE

Napoleon 9500 series Specifications

General

Brand	Napoleon
Model	9500 series
Category	Furnace
Language	English

Summary

Safety Information

Electrical Shock, Fire or Explosion Hazard

Safety warning regarding electrical shock, fire, or explosion hazards.

What to Do If You Smell Gas

Instructions on immediate actions to take if you detect a gas leak.

Introduction

Safety Symbols and Warnings

Safety Rules and Codes

General safety rules, applicable codes, and standards for furnace installation and operation.

Specific Safety Warnings

Important warnings for safe operation, installation, and hazardous situations.

Hazard Specific Warnings

Warnings related to mobile homes, insulation, gas leaks, CO, and control replacement.

Furnace Sizing

Temperature Rise Considerations

Guidance on furnace temperature rise and its relation to airflow and ductwork.

Location of Unit

Installation Location Guidelines

Guidelines for selecting a suitable location and considerations for air supply quality.

Combustible Clearances

Clearance Requirements and Installation Warnings

Clearance requirements for service and installation on combustible floors, with warnings.

Ductwork

Ductwork Sizing, Construction, and Sealing

Standards for ductwork, sealing requirements, and warnings about combustion products.

Venting and Combustion Piping

Acceptable Materials and Installation

Approved materials for venting in Canada and US, and installation requirements.

Non-Direct Vent Furnace Installations

Combustion Air Determination Methods

Determining combustion air for various installation spaces and conditions.

Venting Guidelines

Vent Termination Requirements

Guidelines for vent termination in Canada, US, and preventing single appliance venting.

Routing Options

Exhauster Rotation and Pressure Switch Mounting

Instructions for exhauster rotation and pressure switch mounting, including hose routing.

Condensate Drains

Drain Hose, Piping, and Priming

Instructions for drain hose installation, piping, priming, and warnings about outdoor drainage.

Gas Supply and Piping

Gas Piping and Pressure Management

Gas piping installation, pressure checks, leak testing, and purging procedures.

Conversions

High Altitude and LP Gas Conversions

Modifications for high altitude and conversion procedures from natural to LP gas.

Electrical Specifications

Wiring, Connections, and Grounding

Guidelines for electrical supply, wiring, connections, grounding, and safety warnings.

Furnace Connection

Low Voltage Wiring and Thermostat Location

Low voltage wiring requirements and recommendations for thermostat placement.

Optional Accessories

Accessory Installation and Operation

Instructions for optional accessories like air cleaners, humidifiers, and emergency heat mode.

Startup Procedures

Starting and Shutting Down the Furnace

Step-by-step procedures for starting, shutting down, and operating the furnace.

Sequence of Operation

Flame Failure and Operation Sequence

Explanation of furnace operation sequence and actions during flame failure.

Air Flow

Air Flow and Temperature Rise Checks

Procedures for checking air flow and temperature rise, including calculations and continuous fan operation.

Maintenance and Troubleshooting

Air Filter Maintenance and Cleaning

Instructions for air filter inspection, cleaning, replacement, and warnings.

Routine Examination and Annual Service

Recommended routine checks and annual inspection points for furnace components.

Troubleshooting

Diagnostic Codes and Fault History

Explanation of status LED diagnostic codes and how to access fault code history.

Wire Diagram

Warranty

Warranty Terms and Coverage

Details of limited lifetime and registered/unregistered warranty terms for Napoleon gas furnaces.

Single Stage Replacement Parts List

Warning: Approved Parts Usage

Warning regarding the use of only approved parts to prevent damage or injury.

Furnace Components Diagram

Service History

Appliance Service History Log

Log for recording appliance service dates, technician names, and concerns.

Notes