NEC P627UL Quick Setup Guide

8
Quick Setup Guide
EN
⓪

Install the batteries in the remote control.
• Install new batteries (AAA). Do not mix dierent types of batteries or new and old batteries.
• Ensure that you have the batteries’ polarity (+/−) aligned correctly.
➊
Connect your computer to the projector using the computer cable (VGA). (Not
supplied)
➋
Connect the supplied power cord.
Make sure that the prongs are fully inserted into both the AC IN terminal and the wall outlet.
❸
Remove the lens cap.
With the lens cap’s stopper pressed up, pull forward and o.
❹
Turn on the projector.
WARNING
The projector produces a strong light. When turning on the power, make sure no one within
projection range is looking at the lens.
1. Press the (POWER) button on the projector cabinet or the POWER ON ( ) button on the
remote control.
❺
Select a source.
Detecting the Signal Automatically
1. Press the INPUT button on the projector cabinet or press the SOURCE button on the remote
control.
The projector will search for the available input source and display it.
Using the Remote Control
1. Press any one of the HDMI1, HDMI2, HDBaseT, COMPUTER, USB-A, or APPS buttons.
TIP. Adjusting the Image Using Auto Adjust
Optimizing a computer image automatically. (COMPUTER)
Press the AUTO ADJ. button on the remote control.
❻
Adjust an image size and position.
CAUTION
Perform the adjustment from behind or from the side of the projector. Adjusting from the front
could expose your eyes to strong light which could injure them.
LENS SHIFT
1. Open the lens shift cover.
2. Turn the lens shift dials clockwise or
counterclockwise.
(Horizontal) (Veritical)
3. Close the lens shift cover.
FOCUS
1. Turn the focus ring.
ZOOM
1. Turn the zoom lever.
TILT FOOT
1. Turn the left and right tilt foot to adjust.
❼
Turn o the projector.
1. Press the (POWER) button on the projector cabinet or the STANDBY( ) button on the
remote control.
The conrmation message will be displayed.
2. Press either the (POWER) or the STANDBY( ) button again.
When the light source turns o, the power turns o too (standby mode).

NEC P627UL Specifications

General

HDCP	Yes
Interactive	No
Noise level	27 dB
Certification	CE; EAC; ErP; RoHS; TUEV, TÜV
Projection modes	Ceiling, Front
Number of OSD languages	30
Noise level (economic mode)	22 dB
Native aspect ratio	16:10
Projection distance	0.8 - 12.9 m
Projection technology	3LCD
Contrast ratio (typical)	600000:1
Screen size compatibility	30 - 300 \
Projector native resolution	WUXGA (1920x1200)
Keystone correction, horizontal	-30 - 30 °
Light source type	Laser
Service life of light source	20000 h
Focus	Manual
Focal length range	17.2 - 27.7 mm
Aperture range (F-F)	1.5 - 2.1
Vertical lens shift range	0 - 60 %
Horizontal lens shift range	-29 - 29 %
Analog signal format system	NTSC 3.58, NTSC 4.43, PAL, PAL 60, PAL M, PAL N, SECAM
Supported graphics resolutions	1920 x 1200 (WUXGA), 3840 x 2160
Composite video in	-
HDMI connector type	Full-size
Serial interface type	RJ-45, RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
RMS rated power	20 W
Placement	Ceiling, Desktop
Product type	Standard throw projector
Product color	White
Market positioning	Home cinema
Cable lock slot type	Kensington
Power source	AC
AC input voltage	100-240 V
AC input frequency	50-60 Hz
Power consumption (standby)	0.3 W
Power consumption (typical)	318 W
Power consumption (economy mode)	237 W
Storage temperature (T-T)	-10 - 50 °C
Operating temperature (T-T)	5 - 40 °C
Operating relative humidity (H-H)	20 - 80 %
Remote control type	IR
Quantity per pack	1 pc(s)

Weight and Dimensions

Depth	407 mm
Width	480 mm
Height	122 mm
Weight	9700 g