NEC P547UL User Manual (English)

Questions and Answers:

J
jessicarodriguezAug 16, 2025
How to fix NEC Projector that does not turn on?
- G
  garcialoganAug 16, 2025
  If your NEC Projector doesn't turn on or shut down, there might be a few reasons. First, check if there's enough ventilation around the projector or if the room is too warm; if so, move it to a cooler spot. If the light module isn't lighting up, wait a minute and try turning it on again. Also, if you're using the projector at high altitudes (around 5500 feet/1600 meters or higher), make sure to set the FAN MODE to HIGH ALTITUDE in the settings. As an additional step, you can unplug the power cord, wait 5 minutes, and then plug it back in.
J
Jason BrownAug 19, 2025
Why does my NEC Projector keep turning off?
- Y
  Yesenia SchaeferAug 19, 2025
  If your NEC Projector turns off unexpectedly, make sure that the [OFF TIMER] or [AUTO POWER OFF] settings are disabled.
K
Kelly RussellAug 22, 2025
What to do if my NEC P547UL Projector has no picture?
- T
  Todd SpearsAug 22, 2025
  If you're experiencing a 'no picture' issue with your NEC Projector, here are some things to check: First, ensure the correct input is selected. Verify that all cables are properly connected. Adjust the brightness and contrast settings in the menu. Make sure the AV-MUTE button hasn't been pressed. You may also want to reset the settings to their factory defaults using the RESET option in the Menu. If the Security function is enabled, enter your registered keyword. Reinstall or update the driver for your computer's graphics card. Finally, ensure the projector is in standby mode before connecting it to your notebook PC and turning on the PC.
K
Kristin CordovaAug 25, 2025
How to adjust NEC P547UL Projector image that isn’t square to the screen?
- M
  Morgan YoungAug 26, 2025
  If the image from your NEC Projector isn’t square on the screen, try these solutions: First, reposition the projector to improve its angle relative to the screen. If that doesn't fully correct it, use the Keystone correction function to fix any trapezoid distortion.
R
Rebecca OrtizAug 28, 2025
Why is the NEC P547UL picture blurred and how to fix it?
- J
  Jose AndrewsAug 28, 2025
  If your NEC Projector picture is blurred, try these steps: First, adjust the focus. If that doesn't work, reposition the projector to improve its angle to the screen. Also, ensure that the distance between the projector and the screen is within the lens's adjustment range. Condensation may have formed on the lens if the projector was cold and then brought into a warm place. If so, let the projector stand until the condensation clears.
J
james70Aug 31, 2025
Why does not NEC Projector remote control work?
- N
  nsalasAug 31, 2025
  If the remote control for your NEC Projector isn't working, here are a few things to try: First, install new batteries. Ensure there are no obstructions between you and the projector. Make sure you're within 23 feet (7 meters) of the projector. Note that the remote control sensor on the back of the projector cannot be used when the cable cover is mounted. You can also set the [REMOTE SENSOR] to [HDBaseT] and the [STANDBY MODE] to [SLEEP].
C
crystal57Sep 3, 2025
Why does the NEC P547UL Projector have unusual color tone or hue?
- J
  Jill JosephSep 3, 2025
  If the color tone or hue of your NEC Projector seems unusual, try these steps: First, check if an appropriate color is selected in [WALL COLOR]. If not, select the correct option. You can also adjust the [HUE] setting in the [PICTURE] menu.
D
Donald CardenasSep 6, 2025
What causes image scrolling on NEC P547UL?
- L
  Lance PerezSep 6, 2025
  If the image on your NEC Projector is scrolling vertically, horizontally, or both, try these steps: First, check your computer’s resolution and frequency settings. If adjustments are needed, manually adjust the computer image using the [HORIZONTAL]/[VERTICAL] settings in the [IMAGE OPTIONS] menu.
C
Chad JohnsonSep 9, 2025
Why NEC P547UL Projector picture suddenly becomes dark?
- J
  Jason GriffinSep 9, 2025
  If the picture on your NEC Projector suddenly becomes dark, it might be because the projector is in Forced ECO mode due to a high ambient temperature.
V
Veronica HensonSep 12, 2025
How to resolve cross color in RGB mode on NEC Projector?
- E
  Edward PrattSep 12, 2025
  To address cross color issues in RGB mode on your NEC Projector, try these steps: First, press the AUTO ADJ. button on the remote control. If that doesn't resolve the issue, manually adjust the computer image using the [CLOCK]/[PHASE] settings in the [IMAGE OPTIONS] menu.

NEC P547UL Specifications

General

Native aspect ratio	16:10
Projection distance	0.8 - 12.9 m
Projection technology	3LCD
Contrast ratio (typical)	500000:1
Screen size compatibility	30 - 300 \
Projector native resolution	WUXGA (1920x1200)
Keystone correction, horizontal	-30 - 30 °
Light source type	Laser
Service life of light source	20000 h
Focus	Manual
Focal length range	17.2 - 27.7 mm
Aperture range (F-F)	1.5 - 2.1
Vertical lens shift range	0 - 60 %
Horizontal lens shift range	-29 - 29 %
3D	No
Video color modes	Presentation
Analog signal format system	NTSC 3.58, NTSC 4.43, PAL, PAL 60, PAL M
Supported graphics resolutions	1920 x 1200 (WUXGA), 3840 x 2160
Composite video in	0
HDMI connector type	Full-size
Serial interface type	RJ-45, RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Noise level	26 dB
Certification	CE; EAC; ErP; RoHS; TUEV, TÜV
Projection modes	Ceiling, Front
Number of OSD languages	30
Noise level (economic mode)	22 dB
RMS rated power	20 W
Placement	Ceiling, Desktop
Product type	Standard throw projector
Product color	White
Market positioning	Home cinema
Cable lock slot type	Kensington
Power source	AC
Power consumption (standby)	1.6 W
Power consumption (typical)	293 W
Power consumption (economy mode)	220 W
Recommended gender	Any gender
Storage temperature (T-T)	-10 - 50 °C
Operating temperature (T-T)	5 - 40 °C
Operating relative humidity (H-H)	20 - 80 %
Remote control type	IR