9. Appendix
150
9-11. Troubleshooting Check List
Before contacting your dealer or service personnel, check the following list to be sure repairs are
needed also by referring to the “Troubleshooting” section in your user’s manual. This checklist below
will help us solve your problem more eciently.
* Print this page and the next page for your check.
Frequency of occurrence:
□ always □ sometimes (How often? _________________________ ) □ other ( _____________________ )
Power
□
No power (POWER indicator does not light blue). See also “Status
Indicator (STATUS)”.
□
Power cord’s plug is fully inserted into the wall outlet.
□
Main power switch is pressed to the ON position.
□
No power even though you press and hold the POWER button.
□
Shut down during operation.
□
Power cord’s plug is fully inserted into the wall outlet.
□
[AUTO POWER OFF] is turned o (only models with the [AUTO
POWER OFF] function).
□
[OFF TIMER] is turned o (only models with the [OFF TIMER]
function).
Video and Audio
□
No image is displayed from your PC or video equipment to the
projector.
□
Still no image even though you connect the projector to the PC
rst, then start the PC.
□
Enabling your notebook PC’s signal output to the projector.
• A combination of function keys will enable/disable the
external display. Usually, the combination of the “Fn” key
along with one of the 12 function keys turns the external
display on or o.
□
No image (blue or black background, no display).
□
Still no image even though you press the AUTO ADJ. button.
□
Still no image even though you carry out [RESET] in the projec-
tor’s menu.
□
Signal cable’s plug is fully inserted into the input terminal
□
A message appears on the screen.
( _____________________________________ )
□
The source connected to the projector is active and available.
□
Still no image even though you adjust the brightness and/or
the contrast.
□
Input source’s resolution and frequency are supported by the
projector.
□
Image is too dark.
□
Remains unchanged even though you adjust the brightness
and/or the contrast.
□
Image is distorted.
□
Image appears to be trapezoidal (unchanged even though you
carry out the [KEYSTONE] adjustment).
□
Parts of the image are lost.
□
Still unchanged even though you press the AUTO ADJ. button.
□
Still unchanged even though you carry out [RESET] in the
projector’s menu.
□
Image is shifted in the vertical or horizontal direction.
□
Horizontal and vertical positions are correctly adjusted on a
computer signal.
□
Input source’s resolution and frequency are supported by the
projector.
□
Some pixels are lost.
□
Image is ickering.
□
Still unchanged even though you press the AUTO ADJ. button.
□
Still unchanged even though you carry out [RESET] in the
projector’s menu.
□
Image shows ickering or color drift on a computer signal.
□
Still unchanged even though you change [FAN MODE] from [HIGH
ALTITUDE] to [AUTO].
□
Image appears blurry or out of focus.
□
Still unchanged even though you checked the signal’s resolution
on PC and changed it to projector’s native resolution.
□
Still unchanged even though you adjusted the focus.
□
No sound.
□
Audio cable is correctly connected to the audio input of the
projector.
□
Still unchanged even though you adjusted the volume level.
□
AUDIO OUT is connected to your audio equipment (only models
with the AUDIO OUT terminal).
Other
□
Remote control does not work.
□
No obstacles between the sensor of the projector and the
remote control.
□
Projector is placed near a uorescent light that can disturb the
infrared remote controls.
□
ID for the projector and for the remote are same.
□
Buttons on the projector cabinet do not work (only models with the
[CONTROL PANEL LOCK] function)
□
[CONTROL PANEL LOCK] is not turned on or is disabled in the
menu.
□
Still unchanged even though you press and hold the INPUT
button over 10 seconds.
To Next Page
Loading...
