NETGEAR XS708T Installation Guide

Installation Guide
8-Port, 12-Port, and 16-Port 10-Gigabit Ethernet
Smart Managed Pro Switch with 2 Copper/SFP+
Combo Ports
Model XS708T, XS712Tv2, and XS716T
Package contents
• Switch
• Power cord
• Rubber footpads for tabletop installation
• Rack-mount kit for rack installation
• Installation guide
Note: For more information about installation, see the hardware installation guide, which
you can download from netgear.com/support/.
Discover and register the switch
Use the NETGEAR Insight app to register your switch.
1. On your mobile device, visit the app store, search for NETGEAR Insight, and
download the latest version of the app.
2. Open the NETGEAR Insight app.
3. If you did not set up a NETGEAR account, tap Create NETGEAR Account and follow
the onscreen instructions.
4. Enter the email address and password for your account and tap LOG IN. After you log
in to your account, the switch displays in the devices list.
5. Tap + in the upper right corner.
6. Either use the camera on your phone to scan the serial number bar code located on
the bottom of the switch, or enter the serial number.
7. Tap Go.
8. Follow the onscreen instructions to add your switch to a network location.
9. The switch is registered and added to your NETGEAR account.
For information about how to congure the switch, see the user manual, which you can
download from netgear.com/support/.
Discover the IP address of the switch
An IP address is required to congure your switch. The switch gets an IP address from a
DHCP server (such as your router) by default. If your switch is not connected to a DHCP
server, use the default IP address: 192.168.0.239. If the switch is connected to a WiFi
router or access point, you can use the NETGEAR Insight app to discover the IP address of
the switch.
1. Connect your mobile device to the same WiFi network as the switch.
2. Make sure that the network connects to the Internet.
3. Launch the NETGEAR Insight app from your mobile device.
4. Log in to your account.
The current IP address of the switch displays.
Congure the switch with a static IP address
Note: If your network uses a DHCP server, this section does not apply.
If you are using static IP addresses in your network, congure the switch IP
address before you connect the switch to a network.
Sample connections
XS716T 10-Gigabit Ethernet Smart Managed Pro Switch
WorkstationServer
Connect the switch
ReadyNAS

NETGEAR XS708T Specifications

General

Switch type	Managed
Switch layer	L2+/L3
Quality of Service (QoS) support	Yes
USB 2.0 ports quantity	1
SFP+ module slots quantity	2
Installed SFP modules quantity	-
Basic switching RJ-45 Ethernet ports type	10G Ethernet (100/1000/10000)
Basic switching RJ-45 Ethernet ports quantity	8
Certification	CE, FCC Cl. A, VCCI Cl. A, Cl. A EN 55022 (CISPR 22), Cl. A C-Tick, EN 55024, CCC
Product color	Black
LED indicators	Activity, Link, Power
Number of fans	1 fan(s)
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3an, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Virtual LAN features	Private VLAN, Protocol-based VLAN
Cable types supported	Cat5e, Cat6, Cat6a, Cat7
Copper ethernet cabling technology	10GBASE-T
Noise level	29.1 dB
Flash memory	256 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276832 h
Jumbo frames	9000
Latency (10 Gbps)	3.012 µs
MAC address table	16000 entries
Packet buffer memory	2 MB
Number of static routes	32
DHCP features	DHCP server, DHCP client
Security algorithms	802.1x RADIUS
Access Control List (ACL) rules	100
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	96 W
Operating altitude	0 - 3000 m
Operating temperature (T-T)	0 - 50 °C
Operating relative humidity (H-H)	0 - 90 %
Cables included	AC

Weight and Dimensions

Depth	204 mm
Width	440 mm
Height	43 mm
Weight	2980 g