What to do if the main drive shearbolt fails on New Holland Farm Equipment?
If the main drive shearbolt fails, it may be due to a foreign object or plugging, an overly dense bale, excessively large windrows, too high a feed rate, or shearbolt fatigue. Remove any foreign objects or plugs. If necessary, reduce bale density. Reduce the feed rate by driving slower. Replace the clutch or the shearbolt.
What to do if New Holland Farm Equipment tailgate will not latch?
If the tailgate won't latch, it could be due to crop and stone buildup behind the floor roll, maladjusted latching hooks/pins, or crop buildup in the latching hook area. Clean any crop buildup and stones behind the floor roll. Readjust the tailgate hooks/pins. Clean any crop buildup in the latching hook area.
What causes crop plugging in front of the centering augers in New Holland BR6080?
Crop plugging in front of the centering augers can be caused by excessive weaving, feeding too much crop, maladjusted auger scrapers, or crossing windrows. Improve weaving technique and avoid feeding the entire windrow. Readjust auger scrapers. Raise the pickup when crossing windrows.
Why is bale ejection slow and difficult with New Holland BR6080 Farm Equipment?
Slow or difficult bale ejection can result from insufficient hydraulic flow, bale ejector springs being too tight, high bale density, overfilling the sides of the bale, paint on new bale chamber side sheets, a low PTO speed, or the bale being stuck. Check tractor hydraulics. Release bale ejector springs. Decrease the full bale density setting. Avoid overfilling the sides of the bale. On a new baler, use a lower full bale density until the chamber is polished. Increase PTO speed to at least 450 RPM for ejection. Install special tailgate discs.
How to fix twine that does not start in New Holland BR6080 Farm Equipment?
If the twine does not start, it may be due to feed rolls slipping because of high twine tension, low feed roll tensioner setting, misalignment between feed rolls, tangled twine, improper routing or slippery straw conditions. Reduce twine tension. Readjust the feed roll tensioner. Align the feed rolls. Reroute the twine correctly. In extreme conditions, continue feeding material until the twines start wrapping, then stop immediately.
What to do if the pickup shearbolt fails on New Holland BR6080?
If the pickup shearbolt fails, it may be due to blockages in front of the augers, foreign objects entering the pickup, the pickup hitting the ground in rough fields, or shearbolt fatigue. Reduce ground speed to allow the pickup to tear the bunches apart as they are fed into the machine. Optimize windrow preparation and driving technique. In stony fields, raise the pickup higher off the ground to prevent stones from entering the pickup. Raise the pickup and drive around pot holes in the field. Adjust pickup fol tation lighter (less force needed to lift the pickup). Install new shearbolt.
What to do if New Holland BR6080 does not pick up material cleanly?
If the equipment doesn't pick up material cleanly, it could be due to missing or broken pickup tines, flotation set too light, driving too fast, or the pickup-to-ground clearance being too high. Replace any broken or missing tines. Adjust pickup flotation. Reduce ground speed. Reduce pickup-to-ground clearance.
Why are bales too heavy and dense with New Holland BR6080 Farm Equipment?
Bales that are too heavy and dense may be caused by high crop moisture content, too low ground speed, small windrows, or a full bale density setting that is too high. Allow the crop to dry before baling. Increase ground speed to reduce compaction time. Increase ground speed or rake two windrows together. Decrease the full bale density setting.
What causes pickup plugging in New Holland BR6080 Farm Equipment and how to fix it?
Pickup plugging can occur when feeding large or lumpy windrows too rapidly, or due to incorrect windrow preparation or driving technique, or an incorrect windguard baffle plate adjustment. Reduce ground speed to allow the pickup to tear apart bunches. Optimize windrow preparation and driving technique. Properly adjust the windguard baffle plate.
What to do if New Holland Farm Equipment bales are too light and soft?
If bales are too light and soft, it might be because the ground speed is too high, windrow preparation is improper, or the full bale density setting is too low. Reduce ground speed to allow better compaction. Improve windrow preparation. Increase the full bale density setting.
General| Type | Round Baler |
|---|---|
| Bale Size | Variable |
| Bale Density | Adjustable |
| Minimum Tractor HP | 50 hp |
| PTO Speed | 540 rpm |
| PTO Horsepower | 50-80 HP |
Introduction to the operator's manual and machine operation.
Manufacturer's compliance with directives and standards, including EC Declaration.
General safety guidelines, statements, and reminders for operating the machine.
Listing and location of safety decals for operator guidance and machine safety.
Description of safety guards and their operation to prevent hazards.
Steps for safe operation, including tractor shut down, intended use, and bystander safety.
Procedures for attaching the baler to the tractor, including PTO and hydraulic connections.
Recommended practices for safely towing the agricultural machine on roads.
Importance of lubrication, types of lubricants, and a detailed lubrication chart.
General guidelines for adjustments, periodic inspections, and safety steps before maintenance.
Common concerns, possible causes, and corrections for PTO, pickup, bale formation, and twine wrapping issues.
To Next Page