EasyManuals Logo

Nice Era Mat A Series User Manual

Nice Era Mat A Series
104 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #9 background imageLoading...
Page #9 background image
EN
English – 8
Programs and accessory adjustments
5.10 - Memorization of a SECOND (third, fourth, etc.) transmitter
To perform this procedure you must have a second transmitter (“old”) already memorized.
5.10.1 - Memorization of a second transmitter in “Mode I”
Attention! – This procedure memorizes the new transmitter in “Mode I”, regardless of the Mode in which the old to transmitter was memorized.
Before starting the procedure, bring the rolling shutter to the midpoint of its stroke.
01. (on the new transmitter) Keep pressed the n key for 8 seconds and then release it (in this case the motor does not perform any movement).
02. (on the old transmitter) Give for 3 pulse to the n key, provided it has already been memorized.
03. (on the new transmitter) Give for 1 pulse to the n key to complete the procedure: the motor performs 3 movements. Attention! If the motor performs 6 movements,
it means that its memory is full.
Note When performing the procedure, at any time you can cancel it by keeping the n and t keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements.
5.10.2 - Memorization of a second transmitter in “Mode II”
Attention! – The procedure memorizes a key of the new transmitter in “Mode II”, regardless of the memorization Mode of the key you press on the old transmitter.
Before starting the procedure, bring the rolling shutter to the midpoint of its stroke.
01. (on the new transmitter) Keep pressed for 8 seconds the key you want to memorize (e.g.: n key), then release it (in this case the motor does not perform any
movement).
02. (on the old transmitter) Keep pressed the key n and wait for the motor to perform 4 movements. Upon completion, release the key.
03. (on the old transmitter) Briefly press the n key a certain number of times depending on the and you want to memorize:
1 pulse = Step-by-step command
2 pulses = Open > Stop > Open > Stop > command...
3 pulses = Close > Stop > Close > Stop > command...
4 pulses = Stop command
After about 10 seconds, the motor performs a number of movements equal to the number impulses given with the transmitter.
04. (on the new transmitter) Keep pressed the same key at point 01
and wait for the motor to perform 3 movements. Upon completion, release the key. Attention!
If the motor performs 6 movements, it means that its memory is full.
Note When performing the procedure, at any time you can cancel it by keeping the n and t keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements.
8
sec.
New
0,5
sec.
0,5
sec.
Old
X 3
New
01 02 03
THE
END
3
8
sec.
New Old
01 02
5
sec.
4
1 /
2 /
3 /
4 /
10
sec.
New
Old
03
0,5
sec.
x 1 = Passo-passo
x 2 = Apri > Stop > ...
x 3 = Chiudi > Stop > ...
x 4 = Stop
?
5
sec.
3
04
THE
END
x 1 = Step-By-Step
x 2 = Open > Stop > ...
x 3 = Close > Stop > ...
x 4 = Stop
END
END

Other manuals for Nice Era Mat A Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Nice Era Mat A Series and is the answer not in the manual?

Nice Era Mat A Series Specifications

General IconGeneral
BrandNice
ModelEra Mat A Series
CategoryEngine
LanguageEnglish

Related product manuals