Nice RUN Series - User Manual

Questions and Answers

K
krista83Sep 9, 2025
What causes a photocell to trigger on my Nice Gate Opener?
- A
  Alicia PerezSep 9, 2025
  If a photocell is triggered on your Nice Gate Opener, it means that at the start of the manoeuvre, one or more photocells aren't giving the enable signal. Check for any obstacles and whether the photocells are interfered.
W
Whitney TerrellAug 23, 2025
Why does my Nice RUN Gate Opener remote light up but not work?
- B
  Barbara PhillipsAug 23, 2025
  If the LED on your Nice Gate Opener transmitter lights up but it still doesn't control the gate, the transmitter may not be correctly memorized in the radio receiver. Check the memorization to ensure it is correct.
S
Stephanie WattsAug 25, 2025
What to do if Nice RUN Gate Opener doesn't start and the flasher is flashing?
- M
  michael66Aug 25, 2025
  If your Nice Gate Opener doesn't start and the flasher blinks several times, count the number of flashes. Then, check table 19 in your manual to find out what that number of flashes means.
M
mrichardsonAug 27, 2025
What to do if Nice RUN Gate Opener doesn't start and the flasher is off?
- L
  Larry SalinasAug 27, 2025
  If your Nice Gate Opener isn't starting and the flasher is off, make sure the command is being received. If the command reaches the STEP-BY- STEP input, the corresponding “STEP-BY-STEP” led must light up; if you are using the radio transmitter, the “BlueBus” led must make two quick flashes.
C
Cynthia GilmoreAug 27, 2025
What to do if there is an error in the internal parameters of the Nice RUN?
- A
  Alexandra FranklinAug 28, 2025
  If there's an error in the internal parameters of your Nice Gate Opener's electronic control unit, wait at least 30 seconds and then try giving a command. If the problem continues, it means there's a malfunction, and the electronic board must be replaced.
R
robertbuchananAug 29, 2025
What should I do if my Nice RUN shows an error in the internal electric circuits?
- B
  Brett ThomasAug 29, 2025
  If there's an error in the internal electric circuits of your Nice Gate Opener, disconnect all the power circuits for a few seconds, then try the command again. If the problem persists, it indicates a serious malfunction, and the electronic board needs replacement.
V
Vickie RamirezSep 18, 2025
What should I do if my Nice RUN shows a serious malfunction and the BlueBus LED is on?
- N
  noblemarvinSep 18, 2025
  If your Nice Gate Opener indicates a serious malfunction and the BlueBus LED is on, try switching off the control unit for a few seconds. If the condition persists, it means there is a malfunction, and the circuit board has to be replaced.
J
Jessica MolinaSep 18, 2025
What to check if the STOP input is deactivated on my Nice RUN Gate Opener?
- L
  Lacey KirbySep 22, 2025
  If the STOP input is deactivated on your Nice Gate Opener, check the devices connected to the STOP input.
M
Mrs. Ashley BarnesSep 7, 2025
Why is the Open Gate Indicator not working on my Nice RUN Gate Opener?
- B
  brittany84Sep 8, 2025
  If your Nice Gate Opener is working, but the Open Gate Indicator isn't, check the function programmed for the S.C.A. output (Table 8). When the light should be on, check for voltage on the S.C.A. terminal (approximately 24Vdc). If there is voltage, replace the light with one of the same type. If there's no voltage, the S.C.A. output may be overloaded; check the cable for short circuits.
C
Carla JohnsonSep 4, 2025
Why is my Nice RUN working but the flasher isn't?
- B
  burtonjamesSep 4, 2025
  If your Nice Gate Opener is working but the flasher isn't, first check if there's voltage on the flasher's FLASH terminal during operation (it should be approximately 10-30Vdc). If there is voltage, replace the lamp with one of the same type. If there's no voltage, the FLASH output might be overloaded; check the cable for short circuits.