Nidec PG-35 - Operating Procedures; Multiplier Factor Setting; Analog Output Setting

IntheOperationsMode,pressthe
and buttonssimultaneouslyto
entertheInitialSettingsMode.
Note:Values forthe102R,
forthe103Randthe102A,
and forothertypes,areset
priortodelivery.
TheLEDofanitemflasheswhen
selectedusingthe button.
Pressthe and buttons
simultaneouslytoenterthe
InitialSettingsMode.
Pressthe buttonfor
morethanonesecond
toreturntothe
OperationsMode.
Pressthe buttontomove
tothenextdigit.Thevalue
ofthedigitmaybesetwhen
theLEDbelowthedigitflashes.
Usethe and buttontoset
thevalueofeachdigit.
3
OperatingProcedures
InitialSettingsMode
■MultiplierfactorSetting
■AnalogOutputSetting
Setmagnification
（elevenselections）
Setanalogoutput

（threeselections）
Setswitchoutput

（eightcombinations）
Initial
Settings
Mode
Setting1
Setting2
Hysteresis
（0〜300digits）
DigitalFilter
（F-0〜F-3）
Pressthe and
buttons
simultaneously
Pressthe button
（morethanone
second）
Pressthe and
buttons
simultaneously
Pressthe button
（morethanone
second）
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
Pressthe buttontomove
＋／− SW1 SW2
Third
digit
Multiplierfactor Analogoutput Switchoutput
1：Rmode
2：Gmode
3：Vmode
1〜4：SeparateMode
5〜8：WindowComparatorMode
First
digit
Second
digit
Note:“1”issetpriortodelivery.
Pressthe  buttonuntil
the−LEDunderthe
thirddigitflashes.
Setthevalueofthethird
digitto“4”using
 and
 buttons.
Pressthe buttonformore
thanonesecondtoreturn
totheOperationsMode.
Anexampleofsetting“4”.
※Changeofmagnificationsettingiseffectiveonlyforpressurereading.Setvaluesforswitchingarenotscaledautomatically.
Themultiplierfactorsettingisdeterminedbythevalueofthethirddigit:thered−LEDshouldbeflashingduringthesetting.
Theanalogoutputsettingisdeterminedbythevalueoftheseconddigit:
thegreenSW1LEDshouldbeflashingduringthesetting.
Valueselected
Valueselected
Pressurerange（−Pr〜＋Pr）
Muitiplierfactor
101R 102R 103R 102A
1
2
3
Ｒmode（Compoundpressureoutput）
Ｇmode（Positivepressureoutput）
Ｖmode（Negativepressureoutput）
Mode
−Pr 0 ＋Pr
（Vzero）
1V
1V
1V
5V
5V
5V
Sectionscontaininganobliquestrokearemultiplierfactorthatcannotbeselectedbecauseofresolvingpowerordisplaydigits.
（Valueswillnotbedisplayedautomatically.）
Pressthe buttonuntilthe
SW1LEDunderthesecond
digitflashes.
Setthevalueofthesecond
digitto“1”usingthe and
buttons.
AnexampleofsettingtheRmodeinthe102Rrange.
Notes:Vmodefor102RandRmodefor101Raresetpriortoshipment.R／Gmodefor103RandGmodefor102Acanonlybeselected.
Operations
Mode
kPa
＋／− SW1 SW2
Pressure
Settings
Mode
Intheoperationsmode,press
the and buttonssimultaneously
toentertheInitialSettingsMode.
Pressthe buttonformore
thanonesecondtoreturnto
theOperationsMode.
1
2
3
4
5
6
7
8
9
A
b
−9.99〜9.99
−99.9〜99.9
−75.0〜75.0
−999〜999
−99.9〜99.9
−1.45〜1.45
−2.95〜2.95
−99.9〜99.9
−999〜999
−750〜750
−999〜999
−14.5〜14.5
−29.5〜29.5
−100〜999
−1.02〜9.99
−1.00〜9.99
−14〜145
−0.10〜1.00
−29〜295
0.0〜99.9（abs）
0〜999（abs）
0〜750（abs）
0〜999（abs）
0.0〜14.5（abs）
0.0〜29.5（abs）
×1
×0.0102
×10.2
×7.501
×102
×0.01
×10
×0.145
×0.000145
×0.001
×0.2953
1：× 1
2：×0.0102
3：×10.2
4：×7.501
5：×102
6：×0.01
7：× 1 0
8：×0.145
9：×0.000145
A：×0.001
b：×0.2953
Whenthepowerisswichedon,theOperationsModeisautomaticallyselected.Settingsremainineffectafterswitchingoffthepower.